HP Compaq 6000 Pro SFF Podręcznik Użytkownika

Hardware Reference GuideHP Compaq 6000 Pro Small Form Factor Business PC

Rear Panel ComponentsFigure 1-4 Rear Panel ComponentsTable 1-3 Rear Panel Components1 RJ-45 Network Connector 6 DisplayPort Monitor Connector2 Seria

KeyboardFigure 1-5 Keyboard ComponentsTable 1-4 Keyboard Components1 Function Keys Perform special functions depending on the software application b

Using the Windows Logo KeyUse the Windows Logo key in combination with other keys to perform certain functions available in theWindows operating syste

Serial Number LocationEach computer has a unique serial number and product ID number in the location shown below. Keepthese numbers available for use

2 Hardware UpgradesServiceability FeaturesThe computer includes features that make it easy to upgrade and service. No tools are needed for mostof the

Removing the Computer Access Panel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as c

Replacing the Computer Access PanelSlide the lip on the front end of the access panel under the lip on the front of the chassis (1) then pressthe back

Removing the Front Bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing Bezel BlanksOn some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays thatneed to be removed before inst

Replacing the Front BezelInsert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) thenrotate the top side

© Copyright 2009 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft, Windows, and W

Using the Small Form Factor Computer in a TowerOrientationThe Small Form Factor computer can be used in a tower orientation with an optional tower sta

Installing Additional MemoryThe computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) dual inline memory module

Populating DIMM SocketsThere are four DIMM sockets on the system board, with two sockets per channel. The sockets arelabeled DIMM1, DIMM2, DIMM3, and

will have more memory than the other, the larger amount should be assigned to Channel A. Forexample, if you are populating the sockets with one 1-GB D

7. Rotate up the external drive bay housing to access the memory module sockets on the systemboard.Figure 2-8 Rotating the Drive Cage Up18 Chapter 2

8. Open both latches of the memory module socket (1), and insert the memory module into the socket(2).Figure 2-9 Installing a DIMMNOTE: A memory modu

Removing or Installing an Expansion CardThe computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Expressx16 expansion

7. Locate the correct vacant expansion socket on the system board and the corresponding expansionslot on the back of the computer chassis.8. Release t

b. If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end,and carefully rock it back and forth until the connectors

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansionsocket away from the card and carefully rock the car

About This BookThis guide provides basic information for upgrading this computer model.WARNING! Text set off in this manner indicates that failure to

12. To install a new expansion card, hold the card just above the expansion socket on the systemboard then move the card toward the rear of the chassi

16. If the computer was on a stand, replace the stand.17. Reconnect the power cord and turn on the computer.18. Lock any security devices that were di

Drive PositionsFigure 2-17 Drive PositionsTable 2-3 Drive Positions1 3.5-inch internal hard drive bay2 3.5-inch external drive bay for optional driv

Installing and Removing DrivesWhen installing additional drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected t

CAUTION: To prevent loss of work and damage to the computer or drive:If you are inserting or removing a drive, shut down the operating system properly

System Board Drive ConnectionsRefer to the following illustration and table to identify the system board drive connectors.Figure 2-19 System Board Dr

Removing an External 5.25-inch DriveCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.To remove a

8. If removing an optical drive, disconnect the power cable (1) and data cable (2) from the rear of theoptical drive.Figure 2-21 Disconnecting the Po

10. Press down on the green drive retainer button located on the left side of the drive to disengage thedrive from the drive cage (1). While pressing

8. Install four M3 metric guide screws in the lower holes on each side of the drive. HP has providedfour extra M3 metric guide screws on the front of

iv About This Book ENWW

10. Rotate the drive cage to its upright position.Figure 2-26 Rotating the Drive Cage Up11. Connect the SATA data cable to the white system board con

14. Rotate the drive cage back down to its normal position.CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.Figu

2. Disconnect the drive cables from the rear of the drive, or, if you are removing a media card reader,disconnect the USB and 1394 cables from the sys

3. Press down on the green drive retainer button located on the left side of the drive to disengage thedrive from the drive cage (1). While pressing t

3. Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive towardthe front of the computer until it locks into

Removing and Replacing the Primary 3.5-inch Internal SATA Hard DriveNOTE: The system does not support Parallel ATA (PATA) hard drives.Before you remov

8. Rotate the power supply to its upright position. The hard drive is located beneath the power supply.Figure 2-34 Raising the Power Supply9. Disconn

10. Press down on the green release latch next to the hard drive (1). While holding the latch down,slide the drive forward until it stops, then lift t

12. Align the guide screws with the slots on the chassis drive cage, press the hard drive down into thebay, then slide it back until it stops and lock

Removing and Replacing a Removable 3.5-inch SATA Hard DriveSome models are equipped with a Removable SATA Hard Drive Enclosure in the 5.25-inch extern

Table of contents1 Product FeaturesStandard Configuration Features ...

4. Remove the four screws from the bottom of the hard drive carrier.Figure 2-41 Removing the Security Screws5. Slide the hard drive back to disconnec

6. Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATAconnector on the carrier's circuit board. B

8. Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) andattach the thermal sensor to the top of the ha

A SpecificationsTable A-1 SpecificationsDesktop Dimensions (in the desktop position)HeightWidthDepth3.95 in13.3 in14.9 in10.0 cm33.8 cm37.8 cmApproxi

Rated Line Frequency 50-60 Hz 50-60 HzPower Output 240W 240WRated Input Current (maximum)1STD PSEPA 87/89/85% @ 20/50/100% load PS4A @ 100 VAC4A @ 100

B Battery ReplacementThe battery that comes with the computer provides power to the real-time clock. When replacing thebattery, use a battery equivale

NOTE: On some computer models, it may be necessary to remove an internal component to gainaccess to the battery.8. Depending on the type of battery ho

b. Insert the new battery and position the clip back into place.Figure B-3 Removing a Coin Cell Battery (Type 3)NOTE: After the battery has been repl

C External Security DevicesNOTE: For information on data security features, refer to the Computer Setup (F10) Utility Guide, theDesktop Management Gui

PadlockFigure C-2 Installing a PadlockHP Business PC Security Lock1. Fasten the security cable by looping it around a stationary object.Figure C-3 S

Appendix A SpecificationsAppendix B Battery ReplacementAppendix C External Security DevicesInstalling a Security Lock ...

2. Thread the keyboard and mouse cables through the lock.Figure C-4 Threading the Keyboard and Mouse Cables3. Screw the lock to the chassis using the

4. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage thelock. Use the key provided to disengage the loc

7. Remove one of the five silver 6-32 standard screws located on the front of the chassis behind thebezel.Figure C-7 Retrieving the Front Bezel Secur

D Electrostatic DischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

E Computer Operating Guidelines,Routine Care and Shipping PreparationComputer Operating Guidelines and Routine CareFollow these guidelines to properly

Optical Drive PrecautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation●Do not move the drive dur

IndexAaccess panellocking and unlocking 52audio connectors 2, 4Bbattery replacement 49Ccomputerspecifications 47computer access panelremoving 9replac

removingbattery 49bezel blanks 12computer access panel 9expansion card 20expansion slot cover 21front bezel 11hard drive 39media card reader 35optical

1 Product FeaturesStandard Configuration FeaturesThe HP Compaq Small Form Factor features may vary depending on the model. For a complete listingof th

Front Panel ComponentsDrive configuration may vary by model.Figure 1-2 Front Panel ComponentsTable 1-1 Front Panel Components1 5.25-inch Optical Dri

Media Card Reader ComponentsThe media card reader is an optional device available on some models only. Refer to the followingillustration and table to