HP RP2 Instrukcja Użytkownika

Hardware Reference GuideHP RP2 Retail System

Connecting a serial deviceSome serial devices may require a DB9 connector. Available options from HP are RJ-50 to DB9adapter cables (either 1 meter or

2 Hardware upgradesTools neededA Torx or flat blade screwdriver is needed for most of the procedures described in this guide.Warnings and cautionsBefo

Mounting the RP2 to a wall, swing arm, or pole-mountedbracketThe RP2 can be attached to a wall, swing arm, pole-mounted bracket, or other mounting fix

Unfolding the standThe system ships with the stand in the folded position. To unfold the stand, hold the base down withone hand and push the bottom of

Routing cables to external devices1. Turn off the computer properly through the operating system, then turn off any external devices.2. Disconnect the

6. Insert the tabs on the top of the cable cover into the slots on the rear panel (1) and then rotatethe bottom part of the cover on to secure it (2).

Replacing the power supply1. Turn off the computer properly through the operating system, then turn off any external devices.2. Disconnect the power c

7. Slide the new power supply into the left side of the base.8. Connect the AC power cord to the right side of the power supply inside the base (1), i

10. Replace the side panels on the base. To do so, insert the tabs at the bottom edge of the panelonto the base (1) then rotate the top edge of the pa

Installing optional HP integrated USB peripheral modulesOnly HP approved integrated USB peripheral modules will work with the RP2, such as the HPwebca

© Copyright 2014 Hewlett-PackardDevelopment Company, L.P.Microsoft and Windows are U.S. registeredtrademarks of the Microsoft group ofcompanies.The in

3. Pry off the bottom part of the USB cover plate (1) and then pull the cover plate off the unit (2).4. Pull the plug that is inserted in the USB port

5. Remove the two screws next to the USB port. The screws are needed to install the USB module.6. Slide the screw hole cover plate on the module back

7. Install the two screws that were previously removed (1) and slide the cover plate on the moduleforward to cover the screws (2).8. Reconnect the pow

Installing memoryThe computer comes with one preinstalled double data rate 3 synchronous dynamic random accessmemory (DDR3-SDRAM) small outline dual i

1. Turn off the computer properly through the operating system, then turn off any external devices.2. Disconnect the power cord from the power outlet.

The computer automatically recognizes the additional memory when you turn on the computer.Removing the front panelTo access the internal components of

4. Rotate the display head back to the horizontal position.5. Lift the front panel straight up and off the rear casing.20 Chapter 2 Hardware upgrade

Replacing the front panel1. Place the display head straight down onto the rear casing.2. Tilt the display head up so that you can access the screws th

3. Tighten the four captive screws to secure the rear panel to the casing.4. Connect all cables to the rear I/O connectors, including the power cord.5

Replacing the hard driveCAUTION: If you are replacing a hard drive, be sure to back up the data from the old drive so thatyou can transfer the data to

About This BookThis guide provides basic information for upgrading this computer model.WARNING! Text set off in this manner indicates that failure to

6. Remove the four grommet screws from the sides of the hard drive carrier.7. Slide the hard drive out of the carrier24 Chapter 2 Hardware upgrades

8. Slide the new hard drive into the carrier.9. Install the four grommet screws into the sides of the carrier.Replacing the hard drive 25

10. Align the grommet screws with the slots on the drive bay, drop the carrier straight down into thedrive bay (1), and then press the handle on the c

1. Turn off the computer properly through the operating system, then turn off any external devices.2. Disconnect the power cord from the power outlet.

Securing the RP2 to a counter top1. Turn off the computer properly through the operating system, then turn off any external devices.2. Disconnect the

5. Tilt the neck of the stand (1) and the display head (2) back to their normal positions.6. Reconnect the power cord and press the power button.Insta

PadlockA padlock can be used to secure the RP2 to an external object.1. Install the padlock security loop on the rear panel.NOTE: The padlock security

3 Configuring the softwareTouch screen calibrationYou do not need to install the touch driver software for Microsoft Windows 7 Professional orEmbedded

Configuring powered serial portsThe serial ports can be configured as standard (non-powered) serial ports or powered serial ports.Some devices use a p

A TroubleshootingInterpreting POST diagnostic front panel LEDs andaudible codesThis section covers the front panel LED codes as well as the audible co

iv About This Book

Table A-1 Diagnostic Front Panel LEDs and Audible Codes (continued)Activity Beeps Possible Cause Recommended Actioniteration but LEDs continueuntil p

Table A-1 Diagnostic Front Panel LEDs and Audible Codes (continued)Activity Beeps Possible Cause Recommended ActionPress and hold the power button fo

B Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

C Computer operating guidelines, routinecare and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properly

Shipping preparationFollow these suggestions when preparing to ship the computer:1. Back up the hard drive files. Be sure that the backup media is not

IndexBbattery, replacing 26Ccable routing 8computer operating guidelines 37counter top, securing 28Eelectrostatic discharge, preventingdamage 36Ffeatu

Table of contents1 Product overview ...

Appendix B Electrostatic discharge ...

1 Product overviewProduct ModelsThe HP RP2 Retail System offers 2 (two) base models which include different processors and touchtechnology, as identif

●Sealed and fanless unit●Entire unit rated IP54, water and dust resistant●VESA mounting holes (100 mm x 100 mm and 75 mm x 75 mm patterns )●Flexible u

Rear components1 Optional HP Integrated USB PeripheralModules9 Powered USB 12V2 Hard Drive Activity Light 10 DisplayPort (for a secondary display)3 Se