Hp Tower Uninterruptible Power System Instrukcja Użytkownika Pobierz pdf (Strona 22)

Installation 22

WARNING: To meet the requirements stated in NEC (NFPA 70) Articles 645-10 and 645-11, a

UPS installed in a computer equipment room must be connected to a REPO circuit.

IMPORTANT: The remote switch must be in the Off (open) position to enable power to the output

receptacles.

NOTE: Wire the connector block using stranded, nonshielded wire (AWG #22 - #18, or

equivalent).

Separate wire pairs are attached to a single, normally-open contact in a parallel connection. HP

recommends using different colors for the positive and negative wires.

If a connector becomes disconnected and is reconnected with reversed polarity, a REPO is initiated. To avoid

REPO port disconnect:

• Minimize wire strain while connecting the REPO port.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 79 80

HP R/T3000 G2 UPS 1
User Guide 1
Contents 3
Contents 4 4
Contents 5 5
Contents 6 6
Component identification 7
UPS front panel controls 8
HP UPS R/T3000 models 9
Item Description 10
R/T3000 INT rear panel 11
REPO port 11
ERM rear panel 12
Installation 13
Selecting a site 14
Readying the equipment 14
Installation 15 15
Installation 16 16
Installing the UPS in a rack 17
Connecting the battery leads 18
Installation 19 19
Connecting the host computer 20
Connecting the REPO port 21
Installation 22 22
Installation 23 23
Installation 24 24
Charging the UPS batteries 25
Installing the ERM in a rack 26
Installation 28 28
Installation 29 29
Charging the ERM batteries 30
Installation 31 31
Installation 32 32
Rotating the logo badge 33
Continuing the installation 34
Installation 37 37
Installation 38 38
Installation 39 39
UPS operations 40
Configure mode 41
Battery mode 41
Auto-Bypass mode 41
Configuring the UPS 42
Initiating a self-test 43
Silencing an audible alarm 44
Powering down the UPS 44
Maintenance 45
Obtaining new batteries 47
Maintenance 48 48
Replacing the UPS 49
Replacing the ERM 49
Updating the UPS firmware 50
Power management 53
Power management 54 54
Troubleshooting 55
UPS is in Auto-Bypass mode 56
UPS is in Converter Off mode 57
General alarm condition 57
Bypass is out of range 58
Battery condition 58
UPS is on battery 58
Overtemperature condition 59
Internal UPS fault condition 59
REPO condition 59
Site wiring condition 59
Overload condition 59
Specifications 61
Battery specifications 62
Environmental specifications 63
REPO port specifications 63
Ordering spares 64
UPS spare parts list 64
ERM spare parts list 65
Hardware options 65
Support and other resources 66
Warranty information 67
Recommended duration of use 68
FCC rating label 69
Modifications 70
• EMC Directive 2004/108/EC 71
Japanese notice 72
BSMI notice 72
Korean notice 72
Chinese notice 73
Battery replacement notice 73
Electrostatic discharge 75
Acronyms and abbreviations 76
Documentation feedback 77
Index 78 78
Index 79 79
Index 80 80

Komentarze do niniejszej Instrukcji

Brak uwag

Hp Tower Uninterruptible Power System Instrukcja Użytkownika Strona 22

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Akcesoria komputerowe Hp Tower Uninterruptible Power System