HP Generating Set Instrukcja Użytkownika Strona 11

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 33
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 10
8
Excessive restriction in the exhaust system can be
avoided by proper design and construction. To
make sure you will avoid problems related to
excessive restriction, ask The FG Wilson distributor
to review your design.
The effect of pipe diameter, length and the
restriction of any bends in the system can be
calculated to make sure your exhaust system is
adequate without excessive back pressure. The
longer the pipe, and the more bends it contains, the
larger the diameter required to avoid excessive flow
restriction and back pressure. The back pressure
should be calculated during the installation stage to
make certain it will be within the recommended limits
for the engine.
Measure the exhaust pipe length from your
installation layout. See figure 6.4. Take exhaust
flow data and back pressure limits from the
generating set engine specification sheet. Allowing
for restrictions of the exhaust silencer and any
elbows in the pipe, calculate the minimum pipe
diameter so that the total system restriction will not
exceed the recommended exhaust back pressure
limit. Allowance should be made for deterioration
and scale accumulation that may increase restriction
over a period of time.
Elbow restriction is most conveniently handled by
calculating an equivalent length of straight pipe for
each elbow and adding it to the total length of pipe.
For elbows and flexible sections, the equivalent
length of straight pipe is calculated as follows:
45° Elbow:
Length (ft) = 0.75 x Diameter (inches)
90° Elbow:
Length (ft) = 1.33 x Diameter (inches)
Flexible Sections:
Length (ft): 0.167 x Diameter (inches)
The following formula is used to calculate the back
pressure of an exhaust system:
P =
CLRQ
2
D
5
where:
P = back pressure in inches of mercury
C = .00059 for engine combustion airflow of 100 to 400 cfm
= .00056 for engine combustion airflow of 400 to 700 cfm
= .00049 for engine combustion airflow of 700 to 2000 cfm
= .00044 for engine combustion airflow of 2000 to
5400 cfm
L = length of exhaust pipe in feet
R = exhaust density in pounds per cubic foot
R =
41.1
Exhaust temperature
o
F* 460
o
F+
Q = exhaust gas flow in cubic feet per minute*
D = inside diameter of exhaust pipe in inches
* Available from engine specification sheet
These formulae assume that the exhaust pipe is
clean commercial steel or wrought iron. The back
pressure is dependent on the surface finish of the
piping and an increase in the pipe roughness will
increase the back pressure. The constant 41.1 is
based on the weight of combustion air and fuel
burned at rated load and SAE conditions. See
engine specification sheet for exhaust gas
temperature and air flow. Conversion tables to other
units are provided in Section 12.
FIG 6.4 MEASURING EXHAUST PIPE LENGTH TO DETERMINE EXHAUST BACK PRESSURE
Przeglądanie stron 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 32 33

Komentarze do niniejszej Instrukcji

Brak uwag

Hoshizaki DCM-500BWH-OS manuels

Manuels d'utilisation et guides de l'utilisateur pour Congélateurs Hoshizaki DCM-500BWH-OS.
Nous fournissons des manuels en pdf 1 Hoshizaki DCM-500BWH-OS à télécharger gratuitement par type de document : Manuel de l'utilisateur






Plus de produits et de manuels pour Congélateurs Hoshizaki

Modèles Type de document
KM-250BWF Manuel de l'utilisateur   Hoshizaki KM-250BWF User Manual, 51 pages
F-450MAH(-C) EN Manuel de l'utilisateur   Hoshizaki F-450MAH(-C) EN User Manual, 22 pages
SELF-CONTAINED CRESCENT CUBER L1F015102 Manuel de l'utilisateur   Hoshizaki SELF-CONTAINED CRESCENT CUBER L1F015102 User Manual, 22 pages
KM-320MAH Manuel de l'utilisateur   Hoshizaki KM-320MAH User Manual, 50 pages
STACKABLE CRESCENT CUBER KM-2000SRH3 Manuel de l'utilisateur   Hoshizaki STACKABLE CRESCENT CUBER KM-2000SRH3 User Manual, 29 pages
DB-200H Manuel de l'utilisateur   Hoshizaki DB-200H User Manual, 19 pages
KM-101BAH Manuel de l'utilisateur   Hoshizaki KM-101BAH User Manual, 28 pages
MODULAR CUBELET SERENITY SERIES FS-1022MLH-C Manuel de l'utilisateur   Hoshizaki MODULAR CUBELET SERENITY SERIES FS-1022MLH-C User Manual, 57 pages
SELF-CONTAINED CRESCENT CUBER KM-250BAF Manuel de l'utilisateur   Hoshizaki SELF-CONTAINED CRESCENT CUBER KM-250BAF User Manual, 21 pages
C-100BAF Manuel de l'utilisateur   Hoshizaki C-100BAF User Manual, 40 pages
F-450MAH(-C) Manuel de l'utilisateur   Hoshizaki F-450MAH(-C) User Manual, 20 pages
KM-1601SWH/3 Manuel de l'utilisateur   Hoshizaki KM-1601SWH/3 User Manual, 39 pages
B-1300SS Manuel de l'utilisateur   Hoshizaki B-1300SS User Manual, 17 pages
STACKABLE CRESCENT CUBER KM-2100SWH3 Manuel de l'utilisateur   Hoshizaki STACKABLE CRESCENT CUBER KM-2100SWH3 User Manual, 32 pages
MODULAR FLAKER F-801MAH/-C Manuel de l'utilisateur   Hoshizaki MODULAR FLAKER F-801MAH/-C User Manual, 58 pages
KM-1300SAH-E Manuel de l'utilisateur       Hoshizaki KM-1300SAH-E User Manual, 65 pages
MODULAR CRESCENT CUBER KM-650MWH Manuel de l'utilisateur   Hoshizaki MODULAR CRESCENT CUBER KM-650MWH User Manual, 54 pages
KM-901MWH Manuel de l'utilisateur   Hoshizaki KM-901MWH User Manual, 87 pages
SELF-CONTAINED FLAKER F-500BAF(-C) Manuel de l'utilisateur   Hoshizaki SELF-CONTAINED FLAKER F-500BAF(-C) User Manual, 19 pages
CUBELET ICEMAKER/DISPENSER DCM-750BAH-OS Manuel de l'utilisateur   Hoshizaki CUBELET ICEMAKER/DISPENSER DCM-750BAH-OS User Manual, 69 pages