HP AD583C Instrukcja Użytkownika Strona 61
- Strona / 132
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
e1200-320 4Gb Fibre Channel Interface Card user and service guide 61
• Select 7 to toggle the DHCP setting. This setting enables/disables support for Dynamic Configuration
Protocol. The default setting is enabled. When enabled, the interface card retrieves a dynamic IP
address from a DHCP server located on the Ethernet network that the interface card is connected to.
If DHCP is disabled and then enabled, it is necessary to save the current configuration and reboot the
interface card before an IP address can be requested from the DHCP server. Use the following four
steps:
a. Select X Return to previous menu.
b. Select A Save Configuration.
c. Select X Return to previous menu.
d. Select 4 Reboot.
After the interface card finishes rebooting, the Main menu appears on the serial interface but, for
Telnet, a new session needs to be opened to continue configuring the interface card. DHCP status can
be verified from the Ethernet Configuration menu where DHCP Configuration is indicated as Enabled,
if DHCP has been successfully activated. Note that the IP address may also appear different than the
former non-DHCP IP address.
NOTE: To use the DHCP feature, a DHCP server must be operational on the Ethernet network used by the
interface card. If the DHCP feature is used when there is no DHCP server, the standard for DHCP requires
that the interface card wait three minutes for a response from a DHCP server before timing out.
Your DHCP server may allow you to set up a extended lease reservation for an IP address by
providing the server with the Ethernet MAC address of the interface card. This sets the DHCP server to
always provide the same IP address to the interface card. This setup can be useful for remote
management of the interface card via Telnet or Visual Manager. Because the method of setting up a
lease reservation varies depending on the DHCP server being used, HP recommends that you contact
your Network Administrator for assistance.
• Select 8 to change security settings, including the user name and password. User names and
passwords should be unique and kept confidential and HP recommends using a combination of letters
and numbers when creating user names and passwords.
- HP StorageWorks 1
- Contents 3
- About this guide 7
- HP technical support 8
- 1Introduction 9
- Operation indicators 10
- Processing SCSI information 11
- External indicators 12
- Operating environment 12
- Removal and installation 14
- Installing a new card 16
- Table 4 Cable connections 18
- Number Description 18
- Interfaces and connections 20
- Ethernet connection 21
- Serial port connection 21
- 3 Device management 23
- Discovery 24
- Logical unit management 24
- 26 Device management 26
- 4 Interface card management 27
- Command Line Interface 28
- Visual manager 28
- Inband SCSI-3 commands 29
- 30 Interface card management 30
- Visual manager access 31
- Main menu 32
- Home page 33
- System menu 34
- Serial configuration 35
- Network configuration 36
- Active fabric configuration 37
- Real-Time Clock configuration 39
- Reset menu 40
- Ports menu 41
- SCSI bus configuration 43
- Discovery menu 44
- 2. Select Go 45
- Mapping menu 46
- Statistics menu 48
- Utilities menu 49
- FTP utility access 50
- Trace settings configuration 51
- Event log settings 52
- Event log display 53
- Clear event log 54
- SCSI command tracking 54
- Report menu 55
- Reboot option 56
- Power-up messages 57
- Perform configuration 58
- Baud rate configuration 59
- Ethernet configuration 60
- Fibre Channel configuration 62
- Parallel SCSI configuration 65
- SCSI initiator menu 66
- Maximum SCSI bus speed menu 67
- Device mapping 68
- Adding an entry 69
- Creating an entry 70
- Remove gaps 71
- Deleting an entry 71
- Adding a host 72
- Deleting a host 73
- Editing a host 73
- Trace configuration 75
- Event configuration 76
- Real-Time clock configuration 78
- System utilities 79
- System statistics menu 80
- Channel fabric 81
- Table 7 Fibre Channel status 81
- Event Log 84
- Runtime report 84
- Diagnostics mode 85
- Special FC link control 86
- Get a copy of trace buffer 87
- 7Using the FTP interface 89
- 90 Using the FTP interface 90
- Updating firmware 91
- 92 Using the FTP interface 92
- 8Troubleshooting 93
- Basic verification 94
- Verify SCSI bus configuration 95
- Verify configuration 96
- Verify mapping 96
- Verify devices 96
- Verify host configuration 96
- Running diagnostics 97
- Technical support 97
- 98 Troubleshooting 98
- RJ-11 pin assignments 99
- DB-9 pin assignments 100
- Regulatory compliance 103
- Laser device 104
- European Union notice 105
- BSMI notice 105
- Battery statement 106
- Japanese notice 106
- Korean notices 106
- C Inband SCSI-3 commands 109
- Inquiry command 110
- EVPD Page 0x80 111
- 112 Inband SCSI-3 commands 112
- Indexed addressing option 115
- SCC addressing option 115
- Interface Card 117
- Serial and Telnet interfaces 118
- Visual Manager 121
- Glossary 123
Powiązane produkty i podręczniki dla Networking HP AD583C
Networking HP E5000 Przewodnik Szybki Start
(2 strony)
(2 strony)
Networking HP hn220w Instrukcja Szybki Start
(12 strony)
(12 strony)
Networking HP 3070A Instrukcja Użytkownika
(24 strony)
(24 strony)
Networking HP 24SII Instrukcja Użytkownika
(168 strony)
(168 strony)
Networking HP 510x Podręcznik Użytkownika
(102 strony)
(102 strony)
Networking HP 10-Base-T Instrukcja Instalacji
(54 strony)
(54 strony)
Networking HP 2C Przewodnik Instalacji
(36 strony)
(36 strony)
Networking HP Moonshot-45XGc Podręcznik Użytkownika
(124 strony)
(124 strony)
Networking HP LCS60 Instrukcja Użytkownika
(432 strony)
(432 strony)
Networking HP 6212 Instrukcja Użytkownika
(101 strony)
(101 strony)
Networking HP 3162 Instrukcja Użytkownika
(199 strony)
(199 strony)
Hoshizaki DCM-500BWH-OS manuels
Manuels d'utilisation et guides de l'utilisateur pour Congélateurs Hoshizaki DCM-500BWH-OS.
Nous fournissons des manuels en pdf 1 Hoshizaki DCM-500BWH-OS à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji