HP 6Gb Instrukcja Użytkownika Pobierz pdf (Strona 28)

Clear Configuration task

To delete all user-defined zone groups and server device bay assignments, select the active switch

in the navigation tree, and then click Clear Configuration.

IMPORTANT: If external SAS storage enclosures are connected, before clearing the configuration,

logical units associated with enclosures connected to the switch must be deleted. If a deleted zone

group has disk drives in bays that are configured as part of a logical unit, there may be I/O

problems and the controller may send error messages to the system logs about an illegal drive

movement.

Helpful hints:

• To clear information about a single zone group, use the Delete option. For more information,

see “Delete task” (page 27).

Advanced Settings task

To enter these parameters, select the active switch in the navigation tree, and then click Advanced

Settings.

WARNING! Enable Multi-initiator Mode only after confirming that is it supported for use by the

storage enclosures in your solution. Enabling this mode when not supported by the devices may

result in undefined behavior.

Available parameters:

Multi-initiator

Mode

Controls whether more than one BladeSystem device bay can be assigned the

same zone group.

• Enabled—Allows a zone group to be assigned to multiple BladeSystem server

device bays. Multi-initiator mode should be enabled when shared SAS

storage enclosures, such as the P2000 G3 MSA are connected to the switch.

Enabling more than one initiator (server) to access the same storage enclosure

(zone group) is a key principle of the shared storage concept.

• Disabled—(Default) Restricts a zone group to be assigned to only one

BladeSystem server device bay. Multi-initiator mode should be disabled when

zoned SAS storage enclosures, such as the MDS600 or D2600/D2700 are

connected to the switch. Permitting only one server to access the drives in a

zone group means that those drives will be treated as if they are directly

attached to that server.

Port Splitting

Mode

Controls whether 6Gb SAS BL Switch ports can be divided into sub-ports.

Enabled—Allows a switch port to be divided into two or four separate

sub-ports. When combined with a special cable, port splitting allows you to

connect more tape devices to the switch.

•

• Disabled—(Default)

28 Tasks in the VSM Zoning tab

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 84 85

Komentarze do niniejszej Instrukcji

Brak uwag

Modèles	Type de document
C5J37AWABA	Manuel de l'utilisateur HP C5J37AWABA User's Manual, 165 pages
C6Z78UT#ABA	Manuel de l'utilisateur HP C6Z78UT#ABA User's Manual [no] , 227 pages
Compaq 8300	Spécifications HP Compaq 8300 Specifications, 195 pages
Compaq dc5100	Informations techniques HP Compaq dc5100 System information, 230 pages
Compaq dc5750 SFF	Manuel de l'utilisateur HP Compaq dc5750 SFF User manual, 214 pages
Compaq dc5800	Guide de l'utilisateur HP Compaq dc5800 User guide [en] , 255 pages
Compaq dc7100 DT	Informations techniques HP Compaq dc7100 DT System information, 290 pages
Compaq dx2250	Manuel de l'utilisateur HP Compaq dx2250 User's Manual, 162 pages
Compaq Elite 8000 SFF	Spécifications HP Compaq Elite 8000 SFF Specifications, 284 pages
Compaq Elite 8300 All-in-One	Spécifications HP Compaq Elite 8300 All-in-One Specifications, 168 pages
Compaq Pro 6300 Series Small Form Factor	Spécifications HP Compaq Pro 6300 Series Small Form Factor Specifications [en] , 240 pages
Compaq Professional 5000 series	Guide de dépannage HP Compaq Professional 5000 series Troubleshooting, 74 pages

HP 6Gb Instrukcja Użytkownika Strona 28

Komentarze do niniejszej Instrukcji

HP Cartes mères de serveurs/postes de travail manuels d'utilisation

HP 6Gb Instrukcja Użytkownika Strona 28

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oprogramowanie HP 6Gb

HP Cartes mères de serveurs/postes de travail manuels d'utilisation