HP R1500 Instrukcja Użytkownika

HP UPS R1500 Generation 2 User Guide First Edition (April 2006) Part Number 419178-001

Installation 10 Installation In this section Precautions...

Installation 11 Tools required The following tools are required: Phillips screwdrivers Selecting a site WARNING: To prevent fire or electric shoc

Installation 12 1. Attach the side-mounting brackets to the unit. 2. Loosen the wing nuts, and extend the mounting rails to the desired length.

Installation 13 3. Use the cage nut tool to install cage nuts or clip nuts into the rear of the rack. 4. Insert screws through the mounting rail in

Installation 14 5. Use the cage nut tool to install cage nuts or clip nuts into the front of the rack. 6. Insert a screw through the bottom hole of

Installation 15 2. Attach the chassis to the rack using the supplied screws. 3. (optional) Insert the rear stabilization brackets into the mounting

Installation 16 • Remove watches, rings, or other metal objects. • Use tools with insulated handles. • Do not place tools or metal parts on top of

Installation 17 Selecting the UPS voltage configuration Using a small tool, position the DIP switches according to the desired voltage configuration.

Installation 18 IMPORTANT: Power management software requires the communications port to be appropriately cabled to the host computer. For inform

Installation 19 2. Connect the equipment to the UPS Network Transient Protector OUT jack. Connecting the UPS to utility power WARNING: To preven

© Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties

Installation 20 Powering up the UPS Press and hold the Power On/Standby button (1) until the UPS beeps. The Power On, Load 1 and Load 2 LEDs illumina

UPS operations 21 UPS operations In this section Modes of operation...

UPS operations 22 Battery mode In Battery mode, the UPS supplies power without being connected to utility power. To power up the UPS without using

Power management 23 Power management In this section Power management software...

Maintenance 24 Maintenance In this section Removing the UPS front bezel ...

Maintenance 25 2. Remove the two screws securing the option card and slide the card out. To replace the component, reverse the removal procedure.

Maintenance 26 Battery care and storage guidelines CAUTION: Because of the short shelf life of the batteries, avoid storing a battery spare as a b

Maintenance 27 4. Remove the battery bracket. 5. Remove the UPS battery modules. IMPORTANT: Do not pull the battery leads when removing or insta

Maintenance 28 If the installation has been successful, the UPS enters Operate mode. If the installation has not been successful, the alarm beeps, th

Troubleshooting 29 Troubleshooting In this section LED and audible alarm troubleshooting...

Contents 3 Contents Component identification...

Troubleshooting 30 Condition Power On LED (green) On Battery LED (yellow) Overload LED (red) General Alarm LED (red) Audible alarm Can alarm be silen

Troubleshooting 31 1. If the Overload LED is illuminated, remove one or more load devices to reduce the power requirements. 2. Power down the UPS (&

Specifications 32 Specifications In this section UPS physical specifications...

Specifications 33 Power protection specifications UPS model VA Nominal power rating (W) Nominal voltage setting R1500 G2 NA 1440 1000 110, 1

Specifications 34 Battery runtime Load, percent Load, watts Estimated battery runtime at 100% battery charge 20 200 58 minutes 50 500 17 min

Specifications 35 Pin number Signal name Function Direction from the UPS 7 — No connection — 8 AC fail AC fail relay contact; 20 mA, 30 Vdc conta

Spares 36 Spares In this section Ordering spares...

Technical support 37 Technical support In this section Before you contact HP...

Warranty information 38 Warranty information In this section Limited warranty ...

Warranty information 39 • Notification from power management software

Contents 4 LED and audible alarm troubleshooting ...

Regulatory compliance notices 40 Regulatory compliance notices In this section Regulatory compliance identification numbers...

Regulatory compliance notices 41 Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device,

Regulatory compliance notices 42 Modifications The FCC requires the user to be notified that any changes or modifications made to this device that a

Regulatory compliance notices 43 Disposal of waste equipment by users in private households in the European Union This symbol on the product or on

Regulatory compliance notices 44 Korean notice Class A equipment Class B equipment Battery replacement notice WARNING: Power products contain

Electrostatic discharge 45 Electrostatic discharge In this section Preventing electrostatic discharge...

Acronyms and abbreviations 46 Acronyms and abbreviations IEC International Electrotechnical Commission LED light-emitting diode NEC National Elect

Index 47 A alarm cannot be silenced 29 alarm conditions 29 alarms, silencing 22 alarms, troubleshooting 29 authorized reseller 37 B backup

Index 48 J Japanese notice 43 K Korean notices 44 L LEDs, testing 22 LEDs, troubleshooting 29 LEDs, unit identification 7 limited warranty

Index 49 Test/Alarm Reset button, location 7 testing LEDs 22 tools 11 troubleshooting 29 U Uninterruptible Power System, high-voltage models

Contents 5 Grounding methods to prevent electrostatic discharge... 45

Component identification 6 Component identification In this section UPS front panel...

Component identification 7 UPS front panel controls Item Description Function 1 Power On/Standby button Powers up the UPS ("Powering up

Component identification 8 Item LED description 1 Load Segment 2 2 Load Segment 1 3 General Alarm 4 On Battery 5 Overload 6 Power On For mor

Component identification 9 UPS R1500 G2 INTL rear panel Item Description 1 Input circuit breaker 2 Network Transient Protector IN jack 3 N