Hp ProLiant ML310e Gen8 Server Instrukcja Użytkownika

HP ProLiant ML310e Gen8 Server User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage

Component identification 10 Rear panel LEDs and buttons Item Description Status 1 NIC link LED Green = Link exists Off = No link exists 2 NIC

Acronyms and abbreviations 100 Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility AMP Advanced Memory Protection ASR A

Acronyms and abbreviations 101 FCC Federal Communications Commission HP CS HP Common Slot (power supply) HP SIM HP Systems Insight Manager HP SUM

Acronyms and abbreviations 102 PDU power distribution unit POST Power-On Self Test PXE preboot execution environment RBSU ROM-Based Setup Utility

Acronyms and abbreviations 103 TMRA recommended ambient operating temperature TPM Trusted Platform Module UDIMM unregistered dual in-line memory m

Documentation feedback 104 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documenta

Index 105 A access panel 20, 21 air baffle 21, 22 Array Configuration Utility (ACU) 74 ASR (Automatic Server Recovery) 76 authorized reselle

Index 106 G grounding methods 89 grounding requirements 25 guidelines 30, 47 H hard drives, installing 30, 32 hardware options installation

Index 107 Q QuickSpecs 67 R rack installation 24, 27 rack resources 24 rack warnings 26 RBSU (ROM-Based Setup Utility) 67, 72, 73, 74 rear

Component identification 11 System board components Item Description 1 RPS connector 2 Processor socket 3 System battery 4 24-pin power supply co

Component identification 12 * For more information on the expansion slot specifications, see "PCIe expansion slot definitions (on page 12).&quo

Component identification 13 Switch Default Function 2 Off Off = System configuration can be changed On = System configuration is locked 5 Off Of

Component identification 14 Drive numbering • Four-bay LFF drive model • Eight-bay SFF drive model

Component identification 15 Drive LED definitions Item LED Status Definition 1 Locate Solid blue The drive is being identified by a host

Component identification 16 FBWC module LED definitions The FBWC module has three single-color LEDs (one amber and two green). The LEDs are duplicat

Component identification 17 Fan locations Item Description 1 Rear system fan (fan 1, for processor cooling) 2 Front system fan (fan 2, for ex

Operations 18 Operations Power up the server 1. Connect each power cord to the server. 2. Connect each power cord to the power source. 3. Press t

Operations 19 Unlock the tower bezel The tower bezel must be unlocked and opened to access the drive cage and media bays. It must be unlocked to rem

© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties

Operations 20 2. Close and lock the tower bezel. Remove the access panel WARNING: To reduce the risk of personal injury from hot surfaces, all

Operations 21 c. Lift the access panel away from the chassis. Install the access panel 1. Install the access panel: a. Place the access panel on

Operations 22 1. Power down the server (on page 18). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each

Operations 23 4. Lock the tower bezel. 5. Power up the server (on page 18).

Setup 24 Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and

Setup 25 Space and airflow requirements Leave at least a 7.6-cm (3-inch) clearance space at the front and back of the server for proper ventilation.

Setup 26 includes a nondetachable cord that is wired to an industrial-style plug. NEMA locking-style plugs or those complying with IEC 60309 are con

Setup 27 WARNING: To reduce the risk of personal injury or equipment damage when unloading a rack: • At least two people are needed to safely unl

Setup 28 WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occupational healt

Setup 29 a. Connect the Ethernet cable, and then power on the server. b. During server POST, press the F10 key. c. Complete the initial Preference

Contents 3 Contents Component identification ...

Hardware options installation 30 Hardware options installation Introduction If more than one option is being installed, read the installation instru

Hardware options installation 31 4. Remove the drive carrier. 5. Remove the two metal brackets from the drive carrier. 6. Install the drive in t

Hardware options installation 32 7. Install the drive. 8. Close and lock the tower bezel. 9. Connect each power cord to the server. 10. Connect

Hardware options installation 33 3. Prepare the drive. 4. Install the drive. 5. Determine the status of the drive from the drive LED definitions

Hardware options installation 34 7. Disconnect the drive cage cables: a. Disconnect the Mini-SAS cable from the system board or from the storage co

Hardware options installation 35 10. Attach the hot-plug drive backplane to the drive cage, and then tighten the thumbscrew. 11. Install the drive

Hardware options installation 36 For cable routing information, see "Hot-plug, SATA drive support (on page 62)." — Connect one end of th

Hardware options installation 37 19. Power up the server (on page 18). Eight-bay SFF hot-plug drive cage option To install the component: 1. Power

Hardware options installation 38 9. Install the SFF drive cage assembly. 10. Connect the drive backplane cables: a. Connect the power cable to th

Hardware options installation 39 16. Connect each power cord to the power source. 17. Power up the server (on page 18). Controller options The ser

Contents 4 Drive installation guidelines ...

Hardware options installation 40 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the

Hardware options installation 41 6. Install the cache module on the storage controller. 7. Connect the capacitor pack cable to the cache module.

Hardware options installation 42 9. Install the capacitor pack. 10. Install the air baffle (on page 22). 11. Install the access panel (on page 21

Hardware options installation 43 5. Remove the media bay blank. 6. Remove the EMI shield.

Hardware options installation 44 7. Install the optical drive into the media drive bay. 8. Connect the drive cables: a. Connect the power cable t

Hardware options installation 45 IMPORTANT: This server does not support mixing LRDIMMs, RDIMMs, or UDIMMs. Attempting to mix any combination of t

Hardware options installation 46 Item Description Definition 4 Voltage rating L = Low voltage (1.35V) U = Ultra low voltage (1.25V) Blank or omit

Hardware options installation 47 General DIMM slot population guidelines • The server has four memory slots. • The server supports two channels wi

Hardware options installation 48 7. Install the DIMM. 8. Install the air baffle (on page 22). 9. Install the access panel (on page 21). 10. Lock

Hardware options installation 49 6. Remove the expansion slot cover retainer. 7. Identify the expansion slot compatible with the new option, and t

Contents 5 Array Configuration Utility ...

Hardware options installation 50 8. If installing a full-length expansion board, remove the board retainer. 9. Install the expansion board.

Hardware options installation 51 10. If installing a full-length expansion board, install back the board retainer. 11. Install the expansion slot

Hardware options installation 52 Dedicated iLO management port option To install the component: 1. Power down the server (on page 18). 2. Unlock t

Hardware options installation 53 8. Install the dedicated iLO management module. 9. Install the rear system fan. 10. Install any removed expansio

Hardware options installation 54 HP Trusted Platform Module option Use these instructions to install and enable a TPM on a supported server. This pr

Hardware options installation 55 4. Remove the air baffle (on page 21). 5. Remove any existing expansion board that blocks the access to the rear s

Hardware options installation 56 8. Install the TPM security rivet by pressing the rivet firmly into the system board. 9. Install the rear system

Hardware options installation 57 5. Select Enable, and then press the Enter key to modify the TPM Functionality setting. 6. Press the Esc key to ex

Hardware options installation 58 6. Remove the power supply. 7. Disconnect all cables from installed media drives. 8. Remove all installed device

Hardware options installation 59 10. Insert the RPS backplane module cables into the media drive cage, and then slide in the module into the lower m

Contents 6 Before you contact HP ...

Hardware options installation 60 a. Remove the EMI shield. b. Install the HP CS power supplies. 15. Install any device originally installed in t

Cabling 61 Cabling Cabling overview This section provides guidelines that help you make informed decisions about cabling the server and hardware opt

Cabling 62 Non-hot-plug, SATA and SAS drive support Item Description 1 Power cable 2 Data cable Hot-plug, SATA drive support Item Descriptio

Cabling 63 Hot-plug, SATA and SAS drive support Item Description 1 Power cable 2 Mini-SAS cable Eight-bay SFF drive cabling This drive configur

Cabling 64 Media drive cabling • Media drives in a nonredundant power configuration Item Description 1 Upper media drive power cable 2 Lower med

Cabling 65 Power supply cabling Nonredundant power supply cabling Item Description 1 24-pin power supply cable 2 4-pin power supply cable Re

Cabling 66 Item Description 3 4-pin power supply cable (with the 8-pin to 4-pin adapter cable connected) Capacitor pack cabling

Software and configuration utilities 67 Software and configuration utilities Server mode The software and configuration utilities presented in this

Software and configuration utilities 68 iLO enables and manages the Active Health System (on page 68) and also features Agentless Management. All ke

Software and configuration utilities 69 The data that is collected is managed according to the HP Data Privacy policy. For more information see the

Component identification 7 Component identification Front panel components Item Description 1 Optical drive (optional) 2 Media drive bay 3 USB co

Software and configuration utilities 70 HP Insight Diagnostics HP Insight Diagnostics is a proactive server management tool, available in both offli

Software and configuration utilities 71 HP Insight Remote Support software HP strongly recommends that you install HP Insight Remote Support softwar

Software and configuration utilities 72 HP Service Pack for ProLiant SPP is a release set that contains a comprehensive collection of firmware and s

Software and configuration utilities 73 • Configuring memory options • Language selection For more information on RBSU, see the HP ROM-Based Setup

Software and configuration utilities 74 Boot options Near the end of the boot process, the boot options screen is displayed. This screen is visible

Software and configuration utilities 75 o Advanced Capacity Expansion (SATA to SAS and SAS to SATA) o Offline Split Mirror o RAID 6 and RAID 60 o

Software and configuration utilities 76 For more information about the controller and its features, see the HP Smart Array Controllers for HP ProLia

Software and configuration utilities 77 NOTE: The server ships with the same version programmed on each side of the ROM. Safety and security b

Software and configuration utilities 78 For more information about version control tools, see the HP Systems Insight Manager User Guide, the HP Vers

Troubleshooting 79 Troubleshooting Troubleshooting resources The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedur

Component identification 8 Front panel LEDs and buttons Item Description Status 1 UID LED button Blue = Identification is activated Flashing

System battery replacement 80 System battery replacement If the server no longer automatically displays the correct date and time, you might have to

System battery replacement 81 For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized ser

Regulatory compliance notices 82 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Regulatory compliance notices 83 radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Regulatory compliance notices 84 This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C

Regulatory compliance notices 85 This symbol on the product or on its packaging indicates that this product must not be disposed of with your other

Regulatory compliance notices 86 Class B equipment Chinese notice Class A equipment Vietnam compliance marking notice This marking is for applic

Regulatory compliance notices 87 WARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the

Regulatory compliance notices 88 Acoustics statement for Germany (Geräuschemission) Schalldruckpegel LpA < 70 dB(A) Zuschauerpositionen (bystand

Electrostatic discharge 89 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Component identification 9 Rear panel components Item Description 1 Non-hot-plug power supply 2 Slot 4 PCIe x16 (8, 4, 1)* 3 Slot 3 PCIe x8 (8, 4

Specifications 90 Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Nonop

Specifications 91 HP 350 W 4U Factory Integrated Power Supply Specification Value Input requirements — Rated input voltage 100 V AC to 240 V AC Ra

Support and other resources 92 Support and other resources Before you contact HP Be sure to have the following information available before you call

Support and other resources 93 providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship

Support and other resources 94 Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'in

Support and other resources 95 HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,

Support and other resources 96 sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes

Support and other resources 97 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pel

Support and other resources 98

Support and other resources 99