Hp Integrity rx4610 Server Instrukcja Użytkownika Strona 124
- Strona / 201
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 11: Troubleshooting
117
6. If you suspect a hardware error, follow these steps:
a. Log users off the LAN and power down the HP Server.
b. Extend the HP Server out of the rack and remove the top cover.
c. Simplify the HP Server configuration to the minimum required:
∗ Monitor
∗ Keyboard
∗ Mouse
∗ 1 hard disk drive and 1 flexible disk drive
∗ 1 DVD
d. Remove all third-party options, and reinstall each one, one at a time, checking the HP
Server after each installation.
e. Replace the top cover and reconnect the power cord and other cables.
f. Boot the HP Server and if it does not function properly, refer to the following procedures.
If the HP Server Will Not Power On
Use these steps to check for power related problems:
1. On the control panel, verify the LCD screen's backlight is lit (green glow).
a. If it is lit, the HP Server is receiving AC power.
b. If it is not lit, ensure the HP Server's power cords are connected.
2. Check the HP Server's power supplies.
a. Check that at least three power supplies and both power cords are plugged in to the chassis.
b. Each power supply has three LEDs and the top LED is the Power (PWR) LED.
∗ The top PWR LED glows a steady green when the HP Server's DC power has been
switched on.
∗ The PWR LED will blink green, if the DC power is switched off, but AC power is
properly connected.
3. If the PWR LED on any power supply is not a steady green, reseat the power supply.
4. You can release the lever and then reset it, or remove the power supply from the HP Server.
5. If all power supply LEDs are still blinking green, the HP Server might be in a sleep state.
Refer to your NOS's instructions concerning sleep states.
6. Check that the boards are properly seated.
If the HP Server Powers On but then Shuts Down with a Fault Light
Use this checklist to check for the following problems when the HP Server powers on and then off:
1. Check that a conductive item has not been dropped or left inside the server chassis.
2. Check the connections on all boards.
3. Check the cables for bent pins.
- User Guide 1
- Audience Assumptions 2
- Contents 3
- Open/Close Button 10
- LCD DISPLAY 11
- • +48 V 13
- • +12 V standby 13
- Rear View 14
- Legacy I/O Panel 15
- Powering-Up the HP Server 17
- Powering-Down the HP Server 17
- Mounting the Front Bezel 19
- Main Cover 21
- Replacing the Top Cover 22
- Tools and Supplies Needed 24
- Removing the 172 mm Fans 25
- Hot Swapping the 120 mm Fans 26
- Installing the 120 mm Fans 27
- If only 3 power supplies 28
- Removing a Power Supply 30
- Installing a Power Supply 31
- Mass Storage Guidelines 32
- Tools Required 33
- Determining Drive Status 34
- Removing a Hard Disk Drive 34
- Installing the DVD Drive 37
- Removing the Hard Disk Bay 39
- Installing the Hard Disk Bay 40
- Removing the SCSI Backplane 41
- 1. Disconnect the cable 42
- 2. Remove the two screws 42
- Removing Memory Boards 46
- Installing Memory Boards 47
- Installing DIMMs 49
- Removing DIMMs 51
- Removing a Processor 58
- Figure 6-7. The Triple Beam 62
- Installing Accessory Boards 65
- PCI Hot Plug Slots 68
- Non PCI Hot Plug Slots 68
- Removing Accessory Boards 70
- 8 Server Management Boards 72
- Hot Swap Controller (HSC) 73
- Sideplane cover 75
- Remove protective 75
- Installing the I/O Baseboard 77
- Sideplane Board 78
- PCI Hot Plug LED Board 79
- Legacy I/O Board 81
- Server Management 82
- DVD Cable 82
- Floppy Disk 82
- Drive Cable 82
- Chapter 8: Server Management 83
- Configuring the HP Server 93
- Accelerated Cool Down 100
- FRB3 Timeout 101
- Using BIOS Setup 106
- Using the SELViewer Utility 114
- Using the SDR Viewer Utility 119
- Server Firmware 122
- 11 Troubleshooting 123
- Introduction 123
- Common Installation Problems 123
- Chapter 11: Troubleshooting 125
- BIOS Error Codes\Messages 132
- Beep Codes 136
- Table 11-1. BMC Beep Codes 137
- Types of Memory Tests 138
- User Notification 139
- User Action 139
- Base Memory Test 141
- Error Logging 143
- Extended Memory Test 147
- Examples 149
- Memory Test Duration 150
- Aborting the Memory Test 151
- Setup Dialog 152
- DIMMUTIL 155
- 12 Parts Information 156
- Replaceable Parts List 162
- Parts List Identifier 162
- Appendix A Specifications 165
- Appendix A: Specifications 166
- Video Display Modes 167
- VGA Video Port 168
- Keyboard and Mouse 169
- Parallel Port 170
- Serial Ports A and B 170
- Universal Serial Bus (USB) 172
- Figure A-7. SCSI Connector 173
- Figure A-8. IDE Connector 174
- Information on Jumpers 178
- Legacy I/O Board Jumpers 184
- J7A1 J7A1 186
- I/O Baseboard Jumpers 188
- J8D1 J8D1 189
- Determining DC-to-DC Status 191
- Equipment Log 193
- BMC, 129, 130 195
- Fan Fail LED, 2 196
- Front Panel LCD, 2 197
- General Fault LED, 2 197
- INIT, 2 197
- Index 198
- Power Fail LED, 2 199
- Power On/Off, 2 199
- Reset, 2 199
- Speaker, 129 200
- System Power LED, 2 200
Powiązane produkty i podręczniki dla Sprzęt komputerowy Hp Integrity rx4610 Server
(144 strony)Hoshizaki DCM-500BWH-OS manuels
Manuels d'utilisation et guides de l'utilisateur pour Congélateurs Hoshizaki DCM-500BWH-OS.
Nous fournissons des manuels en pdf 1 Hoshizaki DCM-500BWH-OS à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji