Hp 500B Instrukcja Użytkownika Strona 77
- Strona / 113
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Display "Default BIOS settings have been loaded... Press F10 for Setup, F2 to Continue”. If
the user selects F10, proceed to Setup. However, if the user selects F2, the BIOS should
proceed to step 2 below.
For all other SKUs,
Use F1 instead of F10 in the above handling.
NOTE: If a device fails to respond while the BIOS tries to configure the device during POST, the
BIOS must not make the system look as if it locked up by having an infinite loop or waiting for too
long. Instead, the BIOS must time out after a reasonable amount of time (the time varies with the
device) and skip to the next process.
NOTE: Unless specified in this document as above, the BIOS should not stop the POST process
with any POST diagnostic screen and/or error message to draw user’s attention. For example, HP
does not consider replacing a hard drive or CPU as an error condition.
Power Button/Power Button LED
The power button is under the BIOS control during POST, in BIOS Setup and after booting to a non-
ACPI OS. The BIOS must respond immediately when the power button is pressed in these
environments. For the ACPI-compliant OS such as Windows, the BIOS must pass the power button
information to the OS via the ACPI table as specified in the ACPI spec.
If a platform offers a dual-color-based power button LED, the BIOS will program the power button
LED to alternate the color between the On (ACPI S0) state and the Stand-by (S3) state. In doing so,
the LED should not blink, but stay constant. Check with the corresponding platform manager for the
default colors in the On and Stand-by states. The color of the power button LED in the Hibernate
state (ACPI S4) is the same as in the S5 state.
To find out if the system's power button LED is dual-color capable, check the SMBIOS Type 11 data
structure. If the SMBIOS Type 11 data structure contains the string DLED (NOT case-sensitive), the
system supports the dual-color power button LED and therefore, the BIOS support as described
above is required.
Using the Setup Utility
The BIOS Setup Utility is accessed by pressing the F10 button during startup. The BIOS Setup Utility
allows you to:
●
Change factory default settings
●
Set the system date and time
●
Set, view, change, or verify the system configuration—including settings for graphics, audio,
storage, communications, and input devices
●
View processor and memory settings
●
Modify the boot order of bootable devices—such as hard drives, diskette drives, optical drives,
or USB media
Power Button/Power Button LED
69
- About This Book 3
- Table of contents 5
- 1 Product Description 9
- Product Description 11
- Microtower (MT) Chassis 12
- Access Panel 13
- Front Bezel 15
- DDR3-SDRAM DIMMs 17
- Populating DIMM Sockets 18
- Installing Memory Modules 19
- Expansion Cards 21
- Item Description 22
- 4 PCI expansion slot 22
- Cable Management 29
- Installing Additional Drives 31
- 1 SATA1 SATA0 dark blue 32
- 2 SATA2 SATA1 white 32
- Removing an Optical Drive 33
- Replacing an Optical Drive 35
- Removing a Hard Drive 36
- Replacing a Hard Drive 39
- Power Switch/LED Assembly 42
- System Fan 43
- Power Supply 49
- System Board 55
- Type 1 Battery Holder 57
- Type 2 Battery Holder 58
- Type 3 Battery Holder 58
- A Computer (F10) Setup 60
- Computer Setup—Main 61
- Computer Setup—Advanced 62
- Computer Setup—Power 63
- Computer Setup—Boot 65
- Computer Setup—Exit 66
- B Diagnostics 73
- LED Codes 74
- Testing Memory Modules 75
- POST Error/Warning Messages 76
- Power Button/Power Button LED 77
- Using the Setup Utility 77
- BIOS Updates 78
- Clearing CMOS 78
- Safety and Comfort 80
- Helpful Hints 81
- Solving General Problems 82
- Solving Power Problems 83
- Solving Hard Drive Problems 84
- Solving Display Problems 86
- Solving Audio Problems 87
- Solving Network Problems 88
- Solving Memory Problems 89
- D Connector Pin Assignments 92
- Microphone 93
- Headphone 93
- Line-in Audio 93
- Line-out Audio 93
- 24-Pin Power 94
- PCI Express 95
- Preparation 98
- Grounding the Work Area 100
- Operating Guidelines 101
- Routine Care 102
- Service Considerations 103
- Cables and Connectors 104
- Hard Drives 104
- Lithium Coin Cell Battery 105
- SATA Hard Drives 106
- SATA Hard Drive Cables 106
- SMART ATA Drives 107
- Hard Drive Capacities 107
- G Power Cord Set Requirements 108
- Country-Specific Requirements 109
- H Specifications 110
Powiązane produkty i podręczniki dla Komputery Hp 500B
Komputery Hp SA3150 Instrukcja Użytkownika
(31 strony)
(31 strony)
Komputery Hp AMS DL320 Instrukcja Użytkownika
(86 strony)
(86 strony)
Komputery Hp XW4300 Instrukcja Użytkownika
(90 strony)
(90 strony)
Komputery Hp dc5700 Instrukcja Użytkownika
(216 strony)
(216 strony)
Komputery Hp D2842W Instrukcja Użytkownika
(27 strony)
(27 strony)
Komputery Hp j6700 Instrukcja Użytkownika
(2 strony)
(2 strony)
Komputery Hp ML100 Instrukcja Użytkownika
(111 strony)
(111 strony)
Komputery Hp Compaq Instrukcja Użytkownika
(22 strony)
(22 strony)
Komputery Hp PAVILION DV3 Instrukcja Użytkownika
(114 strony)
(114 strony)
Komputery Hp BL460C G6 Instrukcja Użytkownika
(107 strony)
(107 strony)
Komputery Hp DL185 Instrukcja Użytkownika
(103 strony)
(103 strony)
Hoshizaki DCM-500BWH-OS manuels
Manuels d'utilisation et guides de l'utilisateur pour Congélateurs Hoshizaki DCM-500BWH-OS.
Nous fournissons des manuels en pdf 1 Hoshizaki DCM-500BWH-OS à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji