HP E5000 Podręcznik Użytkownika

HP E5000 Messaging System for MicrosoftExchange Administrator GuideAbstractThis document explains how to install, configure, and maintain all models o

2 Preparing to install the messaging systemBefore you install the messaging system, plan how you will integrate the system into your networkand whethe

Figure 97 Removing the SAS I/O module8. Extend the drive drawer (Figure 54 (page 75)):a. Press upward on the release button on the hard drive drawer (

Figure 99 Removing the plug bracket from the coil power plug10. Unplug the coil power assembly from the midplane board (Figure 100 (page 101)).Figure

Replacing the drive drawer1. Unlock the side enclosure rail and push it into the back enclosure (Figure 102 (page 102)).2. Align the bottom replacemen

Figure 104 Connecting the coil power assembly to the midplane board5. Reattach the plug bracket (1, Figure 105 (page 103)) to the coil power plug and

Figure 106 Pushing the drive drawer into the system enclosure7. Replace the top back panel.8. Replace the drive fan module.9. Replace both SAS I/O mod

2. Extend the hard drive drawer (Figure 107 (page 105)):a. Press upward on the release button on the hard drive drawer (1).b. Pull the drawer handle d

Replacing the drive drawer hard drive1. Install the hard drive (Figure 109 (page 106)):a. Insert the replacement hard drive with the lever in the open

4. Extend the hard drive drawer (Figure 110 (page 107)):a. Press upward on the release button on the hard drive drawer (1).b. Pull the drawer handle d

Figure 112 Unplugging the coil power assembly7. Press the release mechanism on the side rail (1, Figure 113 (page 108)), and then pull the harddrive d

8. Lift the release tab on the side or bottom rail (1, Figure 114 (page 109)), and then slide therail toward the front of the drive drawer to remove t

Figure 3 Network ports6. Server 2, Mezzanine NIC, port 21. Server 1, NIC port 17. Server 1, Mezzanine NIC, port 22. Server 2, NIC port 18. Server 2, M

Figure 116 Partially installing the drive drawer3. Pull the cable slightly out of the coil power plug and connect it to the midplane board(Figure 117

Figure 118 Reattaching the plug bracket to the coil power plug5. Push the drive drawer fully back into the system enclosure (1, Figure 119 (page 111))

3. Extend the hard drive drawer (Figure 120 (page 112)):a. Press upward on the release button on the hard drive drawer (1).b. Pull the drawer handle d

Figure 122 Unplugging the coil power assembly6. Press the release mechanism on the side rail (1, Figure 123 (page 113)), and then pull the harddrive d

Replacing the enclosure rails1. Align the replacement rail, and then attach it by sliding the rail toward the front of the enclosure(Figure 125 (page

Figure 127 Connecting the coil power assembly to the midplane board4. Reattach the plug bracket (1, Figure 128 (page 115)) to the coil power plug and

Figure 129 Pushing the drive drawer into the system enclosure6. Replace the enclosure as described in “Inserting the system enclosure into the rack” (

4. Place the server blade on a flat, level work surface.WARNING! To reduce the risk of personal injury from hot surfaces, allow the drives andthe inte

3. Remove the server blade hard drive (Figure 132 (page 118)):a. Press the release button (1).b. Pull the release lever (2).c. Remove the hard drive (

Removing and replacing the 1210m controller board componentsRemoving the 1210m controller cardWARNING! Wear gloves or use care when removing the capac

• Management network◦ The default setting is dynamic (DHCP) addressing, but you can change this setting asneeded.◦ HP recommends that the management n

9. Remove the capacitor pack (2, Figure 136 (page 120)).The 1210m cache module (1) and the 1210m controller card (3) are also shown.Figure 136 Removin

Replacing the 1210m controller card1. Install the cache module and capacitor in the cache module slot of the replacement controller.2. Close the eject

4. Remove the server blade (Figure 139 (page 122)):a. Push the button to release the handle (1).b. Pull the handle toward you (2).c. Remove the server

Figure 141 Removing the cache module and the capacitor packNOTE: Be sure to first remove the capacitor pack bracket.9. Disconnect the capacitor pack c

2. Complete the following (Figure 143 (page 124)):a. Install the replacement cache module in the cache module slot (1).b. Close the ejector latches on

6. The original capacitor pack is connected to a cache module, so observe the cache moduleLEDs:• If the amber cache LED is solid, data transfer to the

NOTE: Be sure to first remove the capacitor pack bracket.9. Disconnect the capacitor pack cable on the top of the cache module (Figure 147 (page 126))

3. To power off the server blade, click Start and then select Shut down. Verify the server bladeis shut down before continuing.4. Remove the server bl

8 Messaging system recoveryThis chapter describes how to use the E5000 System Recovery DVD that is provided with yourmessaging system.System Recovery

To create a system recovery USB flash drive:1. Obtain a blank 4 GB or larger USB flash drive.2. Insert the USB flash device into your workstation or l

Figure 5 Typical E5500/5700 network configuration4. Domain controller1. Client/MAPI network5. Connection to EMU2. Replication network cable6. Manageme

• C:\ExchangeDatabases\VOL2• C:\ExchangeDatabases\VOL3Restoration in nonproduction environmentsIf the E5300 Messaging System was in a nonproduction en

9 Support and other resourcesContacting HPHP technical supportFor worldwide technical support information, see the HP support website:http://www.hp.co

• http://www.hp.com/storage/whitepapers• http://www.hp.com/solutions/activeanswers/exchangeMicrosoft websitesFor additional Microsoft information, see

10 Documentation feedbackHP is committed to providing documentation that meets your needs. To help us improve thedocumentation, send any errors, sugge

A Managing the EMUThis chapter describes how to manage the EMU using the CLI or the Enclosure Manager physicalinterface.CLI referenceThe CLI is the pr

AuthenticationThis section defines EM authentication CLI functions.ADD SSHKEYSyntaxADD SSHKEY <end marker><newline><certificate><

RestrictionsNoneDOWNLOAD SSHKEYSyntaxDOWNLOAD SSHKEY <url>DescriptionDownloads an authorized key file to use with Secure Shell 2, which can cont

SET PASSWORDSyntaxSET PASSWORD ["<password>"]DescriptionSets the password of the user who entered the command. The <password> pa

SHOW SSHFINGERPRINTSyntaxSHOW SSHFINGERPRINTDescriptionDisplays the key fingerprint of the host public key of the Enclosure Manager.RestrictionsNoneSH

DISABLE NTPSyntaxDISABLE NTPDescriptionDisables the synchronizing of time and date with a remote server using the NTP protocol. Doesnot clear any NTP

3 Installing the messaging systemThis chapter explains how to install the messaging system hardware.Verify the kit contentsRemove the contents, ensuri

Table 15 Universal time zone settings (continued)WSUGreenwichEtc/GMT+11Etc/GMT-6Etc/GMT+0ZuluHSTEtc/GMT-12Etc/GMT+6Etc/GMT-1METEtc/GMT+12Etc/GMT-7Etc/

Restrictions• IPv4 addresses must be in the form ###.###.###.###, where each ### ranges from 0 to255.• IPv6 addresses must be formed without the netwo

SHOW CONFIGSyntaxSHOW CONFIGDescriptionDisplays the script required to recreate the settings of the enclosure. Passwords are not includedfor any user.

SHOW DATESyntaxSHOW DATEDescriptionDisplays the current date, time, and time zone settings of the internal Real Time Clock of theEnclosure Manager.Res

RestrictionsNoneSHOW ENCLOSURE DRIVE DRAWERSyntaxSHOW ENCLOSURE DRIVE DRAWERDescriptionDisplays the state of the enclosure drive drawer. State values

DescriptionDisplays the following general information and current status for the specified power supply orrange of power supplies:• Status (OK, Degrad

SHOW FRUSyntaxSHOW FRUDescriptionDisplays summary information on field replaceable units (FRUs) within the enclosure. Informationprovided in this sect

RestrictionsThe enclosure must be powered on, otherwise, iLO has no power and cannot sense temperatureor send data to the EM.Internet controlThe follo

Restrictions• <ip address> and <netmask> must be in the form ###.###.###.###, where each ###ranges from 0 to 255.• <domain name> is

SET IPCONFIG STATICSyntaxSET IPCONFIG STATIC <ip address> <netmask> [<gateway>]DescriptionConfigures the IP settings for the EM to s

1. If your messaging system is delivered in a rack, proceed to Step 2. If you ordered the messagingsystem without the rack, install the rail kit and e

Restrictions• <bay#> must be 1 or 2.• Use of the FORCE option can cause a server blade to lose data and possibly to becomeunstable.POWERON SERVE

NOTE: Because the EMU hardware cannot determine if a blade is physically present unlessenclosure power is on, the EM reports the warning that the blad

SHOW SERVER LISTSyntaxSHOW SERVER LISTDescriptionDisplays a brief iLO and status description of all server blades. For a longer description, use SHOWS

DescriptionDownloads a previously saved configuration script file from a specific IP host then executes it. Thiscommand should be used to recover conf

SET EM NAMESyntaxSET EM NAME "<EM name>"DescriptionSets the user defined string reported with SHOW EM STATUS. The system responds with

standby power is on. The Unit Identification LED displays as steady on, off, or one of two blinkingspeeds. The system confirms the operation. There is

UPLOAD CONFIGSyntaxUPLOAD CONFIG {<URL>}DescriptionUploads a script to the specified URL, which duplicates the current runtime configuration. Su

RestrictionsThe remote system log server address must be configured before enabling remote system logging.SET REMOTE SYSLOG PORTSyntaxSET REMOTE SYSLO

Restrictions• <bay#> must be 1 or 2.• This command can only function if enclosure power is on. Because the EMU hardware cannotdetermine if a bla

DescriptionOpens a Text Console session to the iLO specified by the server bay number. Exit from the sessionwith ‘exit’.RestrictionsThis command can f

Cable expansion disk enclosuresThe following figures show the correct cabling of expansion disk enclosures to the messagingsystem chassis. Numbers rep

DescriptionSets script mode on or off. script mode prevents commands from prompting for input or confirmation.All actions are performed without confir

Using the Enclosure Manager physical interfaceThe primary interface to the Enclosure Manager is the Ethernet LAN port, which is intended forremote man

Restore Factory Defaults (Fd)You might be replacing an EM or reconfiguring a messaging system. The action resets the EMUaddress to a link local IP add

4. Release the UP button.The system sets the EM to Link local mode and exits the menu mode. This event is also loggedin the EM syslog and takes effect

B E5000 Error CodesE5000 Configuration WizardResolutionDescriptionErrorCodeSee the error message for details. Contact HP support andprovide these deta

ResolutionDescriptionErrorCodeRefer to the error message for details that will accompany thismessage. Contact HP support and provide these details.Err

ResolutionDescriptionErrorCodeSee the error message for details. Contact HP support andprovide these details.Unhandled exception on the Alert Emailsco

ResolutionDescriptionErrorCodeCall HP Support.Class specific storage query failed. Could betiming or problem with specific class.266Verify that System

ResolutionDescriptionPhaseErrorCodeVerify that C:\ExchangeDatabases\VOLx exists(disks are online). You may need to replace physicalEDT Error: Expected

ResolutionDescriptionErrorCodeProgram Files (x86)\Hewlett-Packard\E5000\HPFirmware Update Tool\ .See the error message for details. The UpgradeSelecte

Figure 8 E5700 maximum configuration with four expansion disk enclosures1. E57002–5. Expansion disk enclosures6. SAS cable connecting expansion disk e

ResolutionDescriptionErrorCodeSee the error message for details. This list must be cleared toforce a discovery. No action required.(I) Error clearing

ResolutionDescriptionErrorCodethat there are no unsupported enclosures attached. Thesupported enclosures are D2600 and D2700.See the error message for

ResolutionEventLogEntryTypeDescriptionErrorCodeCheck the provider logs for details.Retry query to provider after threeminutes.WarningEnclosure Provide

ResolutionRoot causeType/SeverityDescriptionErrorCodedirectory or permissions are notconfigured properly on this file.remove the current firmwarebundl

ResolutionRoot causeType/SeverityDescriptionErrorCodeRetry the discovery operation.The system was too busy torespond or the Smart ComponentError/Criti

ResolutionRoot causeType/SeverityDescriptionErrorCodeEnsure that connectivity betweenthe Enclosure Manager and theThe Enclosure Manager cannotbe reach

C TroubleshootingThis appendix addresses common issues and provides information to resolve them.E5000 Configuration WizardResolutionIssueYou are unabl

ResolutionIssueThe disk LUNs/volumes are not set up correctly.• Ensure that all disks are fully seated and run the E5000Configuration Wizard again.• R

ResolutionIssueThe witness server or share cannot be contacted or used.• Open the Exchange Management Shell or the ExchangeManagement Console and run:

PerformanceResolutionIssueRebalance the load using using theRedistributeActiveDatabases.ps1 scriptAll databases are mounted on one server.The System M

1. Connect a system (the configuration system) in the environment or a laptop to the EMU port(Figure 9 (page 18)). You can use either a crossover or a

D Regulatory compliance noticesThis section contains regulatory notices for the HP ______________________.Regulatory compliance identification numbers

off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:• Reorient or relocate the receiving ant

Japanese noticesJapanese VCCI-A noticeJapanese VCCI-B noticeJapanese VCCI markingJapanese power cord statementKorean noticesClass A equipmentClass B e

Taiwanese noticesBSMI Class A noticeTaiwan battery recycle statementVietnamese noticeTaiwanese notices 183

Laser compliance noticesEnglish laser noticeThis device may contain a laser that is classified as a Class 1 Laser Product in accordance withU.S. FDA r

German laser noticeItalian laser noticeJapanese laser noticeLaser compliance notices 185

Spanish laser noticeRecycling noticesEnglish recycling noticeDisposal of waste equipment by users in private household in the European UnionThis symbo

Bulgarian recycling noticeИзхвърляне на отпадъчно оборудване от потребители в частни домакинства в ЕвропейскиясъюзТози символ върху продукта или опако

Estonian recycling noticeÄravisatavate seadmete likvideerimine Euroopa Liidu eramajapidamistesSee märk näitab, et seadet ei tohi visata olmeprügi hulk

Greek recycling noticeΑπόρριψη άχρηοτου εξοπλισμού από ιδιώτες χρήστες στην Ευρωπαϊκή ΈνωσηΑυτό το σύμβολο σημαίνει ότι δεν πρέπει να απορρίψετε το πρ

4. Configure the EMU:a. Connect to the Enclosure Manager software using an ssh compatible tool like PuTTY. Inthe PuTTY session basic options, enter th

Lithuanian recycling noticeNolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās mājsaimniecībāsŠis simbols norāda, ka i

Slovak recycling noticeLikvidácia vyradených zariadení používateľmi v domácnostiach v Európskej úniiTento symbol znamená, že tento produkt sa nemá lik

Battery replacement noticesDutch battery noticeFrench battery notice192 Regulatory compliance notices

German battery noticeItalian battery noticeBattery replacement notices 193

Japanese battery noticeSpanish battery notice194 Regulatory compliance notices

GlossaryCAS Client Access Server. The client access server role is one of five distinct server roles for MicrosoftExchange Server 2010. It supports th

IndexSymbols1210m cache moduleremoving and replacing, 1212-port 1GB Ethernet I/O moduleLED behavior, 512-port 1GB Mezz A and B I/O moduleLED behavior,

restoring the system, 128failure of componentverifying, 73Federal Communications Commission notice, 180firmwarechecking for version upgrade, 45, 66upd

removing and replacing, 85power UID button assemblyremoving and replacing, 84product numberlocating , 14Rrack railsremoving and replacing, 116Rack sta

TTaiwanese notices, 183technical support see Support websitestroubleshooting tools, 34component LEDs, 47EMU CLI SHOW commands, 55Event Notifer, 34Insi

© Copyright 2011, 2012 Hewlett-Packard Development Company, L.P.Confidential computer software. Valid license from HP required for possession, use or

CustomerEMU-dnsName> set passwordNew Password: ********Confirm : ********Changed password for the "Administrator" user account.Custom

Figure 12 Keyboard, mouse, and monitor1. Messaging system enclosure2. Monitor3. Keyboard4. MouseAdding expansion disk enclosures to an installed messa

2. Run the E5000 Configuration Wizard on the first server manually from the All Programsshortcut. The wizard recognizes the new storage and creates ne

4 Configuring the messaging system softwareThis chapter explains how to configure system software using the E5000 Configuration Wizardand how to deplo

IMPORTANT:• By default, the Replication network is set to a static network (10.0.0.0/30) with IP10.0.0.1 on the first node and 10.0.0.2 on the second

5. The wizard displays the status of tasks it must complete before continuing. If the wizard findserrors, it reports them and stops. You must exit the

Figure 15 Computer name10. Review the summary report and complete the configuration. The Summary screen lists theconfiguration settings you have made.

IMPORTANT: Before proceeding:• Install any available software updates as described in “Upgrading E5000 software” (page 61).• Ensure that the Active Di

2. The End User License Agreement Confirmation screen appears. After reading and acceptingthe agreements, click Next.The Jetstress screen appears (Fig

Once you make a selection or if you choose to skip the Jetstress test, click Next. ThePrerequisite Checks screen appears (Figure 18 (page 29)).4. The

Contents1 HP E5000 Messaging Systems for Microsoft Exchange...7Features...

Shell, or additional addresses can be added later using the Set-AvailabilityGroupPowerShell command.• Witness server name. See http://technet.microsof

Figure 19 Deployment statusWhen the process completes, you are prompted to reboot the server. After the reboot, log inagain with Exchange administrato

8. After Microsoft Exchange is deployed on the Bay 2 server, accept the prompt to run theAnalyzer. The Microsoft Exchange Best Practices Analyzer wind

each server in the DAG, you must use an external load balancing method. Two possible methodsare:• Use a hardware load balancer.• Use the Exchange data

5 Monitoring and troubleshooting the messaging systemThe messaging system provides several monitoring and troubleshooting options. You can accessthe f

2. Expand the tree under System Manager.3. In the tree, select Alerts and Email.Figure 21 Configuring Alerts and Email4. Do one of the following:• Sel

Figure 22 Alert and Email settings5. Complete the following fields:• Name—Enter the name of a recipient (for example, John Doe).• Recipient address—En

Figure 23 Send test email7. Click Save. The name of the recipient is displayed on the main Alerts and Email window.To configure the SNMP settings:1. I

HP System Management HomepageThe HP System Management Homepage (SMH) is a web-based interface that consolidates andsimplifies single system management

Figure 24 System Management Homepage main pageThe page provides system, subsystem, and status views of the server and displays groupings ofsystems and

Best practices for replacing components...69During replacement of the

NOTE: A large number of disk errors may indicate that an I/O module has failed. Inspect theI/O module LEDs on the messaging system and any expansion d

NetworkThis section shows the status of the network connections.StorageThis section displays information about the following components:• Storage Syst

NOTE: If read or write cache is enabled the value displayed is 2; otherwise, the value is 3.The Storage Pools page also displays a list of disk drives

Table 1 (page 43) shows the description for the messaging system status tray check mark color.Table 1 System status tray descriptionDescriptionIcon ch

Figure 29 Hardware statusExchange StatusThe Exchange Status tab provides the overall Microsoft Exchange configuration status (by default).Select any c

Figure 30 Exchange statusFirmwareThe Firmware tab indicates whether the firmware of a component is outdated. If the specific firmwarerequires that you

Figure 31 FirmwareReportsThe Reports tab gathers logs for the hardware, software, Microsoft Windows system configuration,and the Microsoft Exchange di

Figure 32 ReportsComponent LEDsLEDs indicate the status of hardware components. This section provides images of the componentLED locations and describ

Table 2 Server blade LEDs status (continued)StatusDescriptionItemOFF = No remote managementGreen = NormalHealth LED2Flashing = BootingAmber = Degraded

Table 3 Front LED status (continued)StatusDescriptionItemFlashing amber (1 Hz) = A predictive failure alert has been received forthis drive. Replace t

10 Documentation feedback...133A Managing the EMU...

Table 4 SAS hard drive LED combinations (continued)StatusDescriptionItemrebuilt.<and>Drive is not rebuilding<and>Drive is not a member of

Table 5 1210m Cache module controller LED status (continued)StatusDescriptionItemGreen flashing (2 Hz) alternating with amber; amber flashing(2 Hz) al

Table 7 HP 2-port 1 GB Ethernet I/O modules LEDs statusStatusDescriptionItemSolid green when module health is goodModule health LED1OFF* when module h

Table 9 Power supply LED statusStatusDescriptionItemGreen = Power on and power supply functioning properly.Power supply1OFF = One or more of the follo

Table 11 SAS I/O module LEDs statusStatusDescriptionItemGreen* = HealthySAS Port 11, 2Amber = IssueGreen* = HealthySAS Port 23, 4Amber = IssueGreen =

EMU CLI SHOW commandsUse the EMU CLI SHOW commands described in “Managing the EMU” (page 134) to obtain additionalinformation about component status a

Figure 44 Recovery LUN ManagerUsing Storage ViewerYou can access Storage Viewer from Manage Storage under System Manager or from the Startmenu on the

Figure 45 Storage Viewer (LUNs view)You can also view details about each drive – bay location, ID, serial number, size, health, andmodel number. In th

HP Support websitesUse the “Support and troubleshooting” task at the HP Support & Drivers website (http://www.hp.com/go/support) to troubleshoot p

Manager. A dedicated server is recommended to host both HP Systems Insight Manager andHP Insight Remote Support Advanced.To implement Insight Remote S

Japanese power cord statement...182Korean notices...

To install the tool:1. Navigte to the C:\hpnas\support directory on the server blade.2. Double click Volume_Manager_Install.msi.To use the tool:1. Nav

6 Upgrading the messaging systemThe E5000 Messaging System is comprised of a common hardware platform containing two serverblades. Each server runs Wi

1. Log in to Server 1 as Domain Administrator.2. Go to www.hp.com/go/support.3. Select Drivers and software.4. Enter E5000 in the Enter a product name

firmware versions are currently installed. See “HP System Management Homepage” (page 38)for more information.Figure 49 System summary tab4. If a firmw

Figure 50 Firmware tab5. On the Firmware tab, select the box next to each component to be upgraded.6. Click Apply Updates. The status reports that an

Figure 51 Component selected for updateCAUTION: When upgrading the 1210m controller firmware, HP recommends that youperform the upgrade in the followi

Figure 52 Firmware status8. Open the Firmware tab in the System Manager and verify that the upgrade was successful.You can also check the upgrade stat

10. Power off the HP E5000 enclosure.11. Push the other server blade back into the enclosure.12. Reconnect the expansion disk enclosures.13. Power on

3. Power off the messaging system enclosure by pressing and holding down the power buttonlocated on the back of the enclosure.4. Disconnect the power

7 Removing and replacing hardware componentsThis chapter describes procedures for removing and replacing hardware components.Customer self repairHP cu

1 HP E5000 Messaging Systems for Microsoft ExchangeThe HP E5000 Messaging System for Microsoft Exchange (“messaging system”) is an integratedhardware-

Identifying the spare partParts have a nine-character spare part number on their label. For some spare parts, the part numberis available in the syste

Figure 53 Exploded view of the systemTable 12 (page 72) lists the CSR replaceable parts for the system.Replaceable parts 71

Table 12 Messaging system replaceable partsReplacement type (Cold,Warm, Hot)CSR availabilityPart numberReplaceable unit (RU)ItemColdOptional631117-001

Table 12 Messaging system replaceable parts (continued)Replacement type (Cold,Warm, Hot)CSR availabilityPart numberReplaceable unit (RU)ItemWarmOption

the controller enclosure blinks. See “HP System Management Homepage” (page 38) for moreinformation.• Look for a blinking amber LED on the component. S

Removing the system enclosure from the rack1. Extend the hard drive drawer (Figure 54 (page 75)):a. Press upward on the release button on the hard dri

7. Unscrew the retaining screws from the bezel ears, and then remove the enclosure from therack.WARNING! The system enclosure is heavy, even after rem

4. Remove the top back panel by pressing the panel release button and lifting the latch to slidethe top back panel off.5. Open the release handle (1,

Removing and replacing the midplane boardRemoving the midplane board1. Verify the failed component as described in “Verifying component failure” (page

8. Unplug the coil power assembly from the midplane board (Figure 61 (page 79)).Figure 61 Unplugging the coil power assembly9. Extend the server blade

Figure 1 Front view1. Disk drive drawer2. Server blade 1, Bay 13. Server blade 2, Bay 24. Chassis fault LEDFigure 2 Rear view1. System fan2. HP 2-port

12. Complete the following (Figure 64 (page 80)):a. Loosen the two thumbscrews holding midplane board in place (1).b. Pull the captive locking pin out

11. Replace the top back panel.12. Reinsert all rear components in the enclosure.13. Replace the enclosure in the rack as described in “Inserting the

5. Push down on the SAS I/O module lever (2, Figure 66 (page 82)), and then remove the failedSAS I/O module (3, Figure 66 (page 82)).NOTE: You may nee

4. Confirm the firmware version.5. Confirm that the system has resumed normal operations.Removing and replacing the fan moduleThere are two fan module

Replacing the fan module1. Insert the replacement fan module (Figure 69 (page 84)).Figure 69 Replacing the fan module2. Verify that the replacement co

5. Complete the following (Figure 71 (page 85)):a. Unplug the cable from the power UID button assembly (1).b. Remove the screw from the power UID butt

Replacing the power supply1. Insert the replacement power supply.2. Plug the power cord into the power supply.3. Verify that the replacement component

3. Verify that the replacement component is working properly by checking the associated LEDstatus.NOTE: It should take approximately 15 seconds for th

7. Complete the following (Figure 76 (page 88)):a. Remove the two screws from the bracket of the failed PCIe module (1).b. Remove the bracket (2).c. R

Figure 78 Installing the PCIe module3. Plug in all cables to the PCIe module in their original locations.4. Power on the server blade by pressing the

Configuration Wizard and HP E5000 Messaging System Exchange Deployment Tool, which areused to deploy the Exchange servers and storage in their optimal

Replacing the EMU module1. Insert the replacement EMU module and ensure the release lever locks in place (Figure 80(page 90)).Figure 80 Installing the

8. Complete the following (Figure 81 (page 91)):a. Unplug the power cable from the server blade backplane by pinching the plug releasemechanism (1).b.

4. Replace the midplane board (Figure 83 (page 92)):a. Pull out the captive locking pin as you lower the board into the enclosure (1).b. Push the capt

Replacing the server airflow baffle1. Install the replacement server blade airflow baffle (Figure 85 (page 93)).Figure 85 Installing the server blade

3. Remove all eight screws from the front bezel (1, Figure 87 (page 94)), and then lift the frontbezel up and out to remove the front bezel (2).NOTE:

Removing and replacing the front bezel (full)NOTE: This full procedure is only required if all screws are not accessible due to the position ofthe sys

Replacing the front bezel (full)1. Install the replacement front bezel with the handle at a 90 degree angle, making sure thebottom pins are aligned wi

4. Complete the following (Figure 91 (page 97)):a. Disconnect the LED display board from the drive backplane by pinching the ends of theLED display bo

4. Pull the hard drive drawer handle down 90 degrees, and slide out the hard drive drawer.5. Remove all eight screws from front bezel (1, Figure 93 (p

Replacing the front LED display board (full)1. Complete the following (Figure 95 (page 99)):a. Install the replacement LED display board (1).b. Replac