Hp Insight Management WBEM Providers Instrukcja Użytkownika

HP Insight Management WBEM Providers UserGuidePart Number:edition: September 2010 (Eighth Edition)

NOTE:The Configure or Repair Agents tool can update multiple target systems, each of which mighthave different results. The log results indicate wheth

You can install the Insight Providers individually using an Insight Providers Smart Component. Performthis type of installation to install the Insight

d. Select the Security tab.e. Select the namespace.f. Click the Security button. For the standard user, verify that permissions are set as follows:• E

3 Uninstalling SNMP-Based HP InsightManagement AgentsIntroductionThis section provides instructions for uninstalling the SNMP-based HP Insight Managem

• For Windows Server® 2003, click Remove.• For Windows Server® 2008, right-click, and select Uninstall.5. At the prompt, to confirm the removal of HP

4. Verify that OpenSSH is installed on the target servers.If OpenSSH is not installed, install it on the target servers:a. From the HP SIM menu, selec

command resets the HP System Management Homepage.Scripting commands for HP Insight Management Agents 7.70 or laterTo uninstall HP Insight Management A

4 Using the SMH with the Insight ProvidersChange Data SourceThe SMH now enables data collected from the Insight Providers or SNMP agents. After the In

• HP_ThresholdIndication• CIM_ThresholdIndication• CIM_AlertIndication• CIM_ProcessIndication• CIM_Indication• CIM_OperatingSystemIf the server is bei

5 SecuritySecurity concernsUsers can increase security by switching from SNMP Agent-based server management to InsightProvider-based server management

Notices© Copyright 2008, 2010 Hewlett-Packard Development Company, L.P.The information contained herein is subject to change without notice. The only

Configuring Insight Provider Security for a User Account usingHP SIM Configure and Repair AgentsNOTE:When you must configure a non-administrator accou

a. In the User name field, enter a user name.b. In the Password field, enter the password for the user.c. In the Password (Verify) field, re-enter the

•EnableRWMI -a:domain\userSecurity22

6 Windows Server® 2008 FirewallconfigurationFirewall configuration introductionThis section describes a configuration method for enabling direct remot

An additional firewall rule is needed to enable a remote user to establish a WMI session. It can beenabled with the following command:netsh advfirewal

7 Insight Providers architectureArchitecture overviewThe following architecture diagram gives an overview of Insight Provider components. The diagrami

• Sensor information and indications, including redundancy, fans, temperature sensors, andpower supplies• Computer system information, including physi

LinkVer-sionProfile namehttp://www.dmtf.org/standards/published_documents/DSP1013_1.0.1.pdf(http://www.dmtf.org/standards/published_documents/DSP1013_

VersionProfile/Subprofile name1.2.0Block Services Package1.3.0Disk Drive Lite Subprofile1.2.0Multiple Computer System Subprofile1.3.0Disk Sparing Subp

File nameVersionProfile nameP00107_-_HP_CPU_Consolidated_Status_Profile.pdf1.0.0P00107 HP CPU ConsolidatedStatus ProfileP00108_-_HP_CPU_Physical_Asset

Contents1 Introduction ... 5Overview ...

Microsoft Visual Basic Scripting Edition examplesYou can write scripts to obtain data from the Insight Providers using Microsoft® Visual Basic Scripti

Set colComputerSystemChassis = objWMIService.ExecQuery("Select * from HP_ComputerSystemChassis")For Each objComputerSystemChassis in colComp

For Each objFan in colFanWScript.Echo "Caption: " & objFan.CaptionWScript.Echo "Description: " & objFan.DescriptionFor Eac

Insight Providers usageAccess data and events from the Insight Providers using the SMH supplied in the PSP, HP SIM, otherclient applications, or scrip

Insight Providers architecture34

8 ScriptingScripting examplesThis section provides examples for accessing data exposed by the Insight Providers using scripting.WMIC exampleYou can al

Scripting36

9 Support informationOperating system supportThe operating systems in the following table are supported by version 2.7.0 of the Insight Providers.For

CommentsOperating System—Windows Server® 2008 Enterprise 32-bit Edition—Windows Server® 2008 Datacenter 32-Bit Edition—Windows Server® 2008 Standard E

10 Technical supportReference documentationFor more information about PSPs, see the PSP website (http://www.hp.com/servers/psp).To download the latest

Architecture overview ... 25Data model ..

Technical support40

Acronyms and abbreviationsAPI application program interfaceASR Automatic Server RecoveryCIM common information modelDMTF Distributed Management Task F

Acronyms and abbreviations42

IndexAaccess rights, setting userConfiguring Insight Provider Security usingthe Windows Command Line, 21Implementation, 19Security requirements for th

Ooperating systems supported, 37overview, WBEM Providers, 5Ppreinstallation, guidelinesInsight Providers Smart Component, 7Installing the Insight Prov

System Management Homepage, datacollection, 18System Management HomepageAuto Refresh, 17Data collection, 18Using the SMH with the Insight Providers, 1

46

1 IntroductionOverviewThis document applies to the HP Insight Management WBEM Providers for Windows Server® 2003,Windows Server® 2008, and Windows HPC

Introduction6

2 Installing the HP Insight ProvidersInsight Providers Smart ComponentHP Insight Providers include server, storage, and network providers as well as W

4. To begin the installation, run setup.exe or HPSUM.exe.This action initiates the HP Smart Update Manager graphical interface and opens the SourceSel

For detailed installation instructions, see the HP SmartStart documentation.4. At the Server Deployment - Management Instrumentation screen, select HP