Hp Tape Library Interface Manager Software Instrukcja Użytkownika Pobierz pdf (Strona 59)

Chapter 3 Management Operations 59

Chapter 3

Figure 10 Interface Manager Network Settings

Using DHCP

If the DHCP system is to be used:

1. Select [Obtain network parameters automatically from a DHCP/BOOTP

server] radio button. This enables the DHCP mode.

2. Select the [Apply] button to load the configuration into the RMC.

These settings are not put into effect until the next power cycle or next RMC

reboot. None of the Fibre Channel interface cards are adversely affected by

this function, so this can be done while data is flowing through the interface

cards.

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 137 138

Part Number: C9578-90000 1
Edition 1 1
December 2001 1
In this manual 2
Warranty 3
Reference Standards 4
Chapter 1 Introduction 11 5
Chapter 4 SAN Environments 77 8
Introduction 11
12 Introduction Chapter 1 12
Chapter 1 Introduction 13 13
Processing SCSI Information 14
Fibre Channel Features 15
SCSI Bus Features 15
Configuration Features 15
Management Features 16
Chapter 1 17
Table 2 Supplied Components 18
No. Item Qty Description 18
Specifications 19
Supported Products 20
Chapter 1 Introduction 21 21
Optical Fibre Channel Cables 22
Interface Manager Overview 23
Chapter 2 27
Fibre Channel Port Mode 28
Hard Addressing 29
Soft Addressing 29
Host Device Configuration 30
SCSI Addressing 30
Buffered Tape Writes 30
Address Mapping 31
Auto-Indexed Mapping 32
Fixed-Indexed Mapping 32
Configuration Methods 33
Web Based Administrator 34
Management Operations 35
Management Interfaces 36
Overview 38
Accessing Telnet 38
Chapter 3 41
Table 7 Time Zones 41
Using Your Own Settings 44
Setting Date and Time 56
Time Shown is NOT Correct 57
Using DHCP 59
Administrator 60
Hard Address Settings 62
Soft Address Settings 62
Selecting Your Own Settings 63
Using the Web Interface 72
Upgrade Firmware Using FTP 74
FTP Interface (Single Card) 75
SAN Environments 77
Chapter 4 79
80 SAN Environments Chapter 4 80
Omniback Configuration 81
82 SAN Environments Chapter 4 82
Chapter 4 SAN Environments 83 83
Configuration on page 85 84
HP-UX Configuration 85
86 SAN Environments Chapter 4 86
Chapter 4 SAN Environments 87 87
Stopping the dm_stape process 88
90 SAN Environments Chapter 4 90
Chapter 4 SAN Environments 91 91
file to 91
Windows Configuration 92
Solaris Configuration 94
Switch Configuration 95
96 SAN Environments Chapter 4 96
Troubleshooting 97
Operation Indicators 99
100 Troubleshooting Chapter 5 100
Chapter 5 Troubleshooting 101 101
102 Troubleshooting Chapter 5 102
Basic Verification 103
104 Troubleshooting Chapter 5 104
NT Control Panel 104
Chapter 5 105
1. Execute an ioscan command 105
Figure 29.) 105
Figure 29 ioscan Sample 105
106 Troubleshooting Chapter 5 106
Problem - Solution 107
108 Troubleshooting Chapter 5 108
Chapter 5 Troubleshooting 109 109
110 Troubleshooting Chapter 5 110
Chapter 5 Troubleshooting 111 111
112 Troubleshooting Chapter 5 112
114 Troubleshooting Chapter 5 114
DB-9 Serial and RJ-45 115
Ethernet Pin Assignment 115
RJ-45 Pin Assignments 116
Fibre Channel Interface and 117
Commands 117
■ Byte 2 set to 0xFA 118
Report LUNs Command 119
PRLI Data 121
SCSI Interface and Commands 123
Customer Support 125
Glossary 127 127
128 Glossary 128
Glossary 129 129
130 Glossary 130
Glossary 131 131
132 Glossary 132
Glossary 133 133
134 Glossary 134
Glossary 135 135
World Wide Name 136
Index 137 137
138 Index 138

Komentarze do niniejszej Instrukcji

Brak uwag

Hp Tape Library Interface Manager Software Instrukcja Użytkownika Strona 59

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Przechowywanie Hp Tape Library Interface Manager Software