HP EliteDesk 800 G4 Base Model Small Form Factor PC Instrukcja Użytkownika Strona 79
- Strona / 144
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Table 5-2 Computer Setup—Security (continued)
Option Description
Displays the current TPM version.
●
TPM Device
Lets you set the Trusted Platform Module as available or hidden.
●
TPM State
Select to enable the TPM.
●
ClearTPM
Select to reset the TPM to an unowned state. After the TPM is cleared, it is also turned o. To
temporarily suspend TPM operations, turn the TPM o instead of clearing it.
CAUTION: Clearing the TPM resets it to factory defaults and turns it o. You will lose all created
keys and data protected by those keys.
BIOS Sure Start
●
Verify Boot Block on every boot. Default is disabled.
●
BIOS Data Recovery Policy. Default is Automatic.
IMPORTANT: Only select Manual in situations in which forensic analysis is to be performed before
HP Sure Start Recovery. When this policy is set to manual, HP Sure Start will not correct any issues
that are found until the manual recovery key sequence is entered by the local user. This can result in
a system that is unable to boot after inputting the manual recovery key sequence.
●
Sure Start BIOS Settings Protection. This setting requires setting the BIOS Administrator password.
Default is disabled.
●
Sure Start Secure Boot Keys Protection. Default is enabled.
●
Enhanced HP Firmware Runtime Intrusion Prevention and Detection. Enables monitoring of
rmware executing out of main memory while the operating system is running. Any anomalies
detected in rmware that are active while the operating system is running results in generation of a
Sure Start Security Event. Default is enabled.
●
Sure Start Security Event Policy. Controls HP Sure Start behavior upon identifying a critical security
event (any modication to rmware) during operating system runtime. When set to Log Event Only,
HP Sure Start logs all critical security events. When set to Log Event and Notify User, HP Sure Start
noties the user that a critical event has occurred. When set to Log Event and Power O System, HP
Sure Start powers o the system upon detecting a security event. Default is Log Event Only.
●
Sure Start Security Event Boot Notication. Default is Require Acknowledgment.
HP Secure Platform Management (SPM)
●
HP Sure Run Current State (Inactive/Active)
●
Deactivate HP Sure Run
●
SPM Current State (Not provisoned/Provisioned)
●
Unprovision SPM
Physical Presence Interface. Noties the user upon system power up when changes are made to system
security policy. The user must agree to the changes to conrm them. Default is enabled.
Smart Cover
●
Cover Lock. Default is ‘Unlock’.
●
Cover Removal Sensor. Lets you disable the cover sensor or congure what action is taken if the
computer cover was removed. Default is ‘Disabled’.
Computer Setup (F10) Utilities 71
- Maintenance and Service Guide 1
- Safety warning notice 3
- Table of contents 5
- 1 Product features 9
- Front panel components 10
- Rear panel components 11
- Serial number location 11
- 2 Illustrated parts catalog 12
- Computer major components 5 13
- Miscellaneous parts 15
- Generating static 17
- Grounding the work area 18
- Operating guidelines 19
- Routine care 20
- Service considerations 21
- Cables and connectors 22
- Hard Drives 22
- Lithium coin cell battery 22
- SATA hard drives 23
- SATA data cable 23
- SMART ATA drives 23
- Cable management 24
- Preparation for disassembly 25
- Access panel 26
- Front bezel 27
- Front bezel dust lter 29
- System board connections 30
- Populating DIMM sockets 31
- Removing and installing DIMMs 32
- Expansion card 34
- Expansion card 27 35
- Drive positions 38
- Drives 35 43
- Drives 37 45
- Drive cage 48
- WLAN module 54
- Hood lock 55
- Card reader 56
- Antennas 57
- Air duct 59
- Option board 60
- Optional rear port 61
- Fan sink 62
- Up to 65 W processor models 63
- 95 W processor models 63
- Fan sink 55 63
- Processor 66
- Power supply 67
- System board 69
- System board callouts 72
- Computer Setup–Main 76
- Computer Setup—Security 78
- Computer Setup—Advanced 81
- Computer Setup—UEFI Drivers 86
- Safety and comfort 87
- Helpful hints 88
- Solving general problems 89
- Solving general problems 83 91
- Solving power problems 93
- Solving hard drive problems 94
- Solving display problems 97
- Solving display problems 91 99
- Solving audio problems 101
- Solving printer problems 103
- Solving network problems 106
- Solving network problems 99 107
- Solving memory problems 109
- Solving software problems 114
- Resetting the password jumper 122
- A Battery replacement 130
- B Power cord set requirements 133
- Country-Specic Requirements 134
- Nonvolatile memory usage 137
- Questions and answers 139
- D Specications 141
Powiązane produkty i podręczniki dla Nie HP EliteDesk 800 G4 Base Model Small Form Factor PC
(62 strony)
(2 strony)
(90 strony)
(14 strony)
(5 strony)
(18 strony)
(201 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji