Hp Netserver L Server series Instrukcja Użytkownika Strona 38
- Strona / 146
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 4 Installing Additional Memory
32
Memory Installation Guidelines
• The HP Netserver LP 2000r only uses PC 133 (133 MHz) SDRAM DIMMs,
which are electrically different from the EDO and PC100 SDRAM memory
modules used in previous HP Netserver models.
• DIMMs sizes supported are 128 MB, 256 MB, 512 MB, or 1 GB in any
combination.
• Supported memory capacity ranges from 128 MB to 4 GB maximum
(1 GB DIMM in each of the 4 DIMM slots).
• DIMM sizes may be mixed on the system board and may be loaded in any
order (0 through 3). However, HP recommends starting at slot 0 and filling
the slots in order with the largest size first: 0, 1, 2, and 3.
• Open slots between DIMMs are permitted.
• When handling DIMMs, observe anti-static precautions to avoid damage.
Installing Additional DIMMs
1. Log off all users, back up files, and power down the HP Netserver.
For detailed instructions, see "Powering-Down the HP Netserver," in
Chapter 1, "Controls, Ports and Indicators."
2. Pull out the anti-tip foot at the bottom of the rack. Then extend the HP
Netserver chassis out from the rack.
It is not necessary to remove the HP Net Server from the rack to install
DIMMs.
3. Disconnect the power cables and any external cables connected to the system.
If necessary, label each one to expedite reassembly.
WARNING The power supply will continue to provide standby current to
the HP Netserver LP 2000r until the power cable is
disconnected.
4. Remove the top cover.
Refer to "Removing the Top Cover" in Chapter 2, "Opening and Closing the
HP Netserver."
5. Remove the air flow guide. See Figure 4-1.
Refer to "Removing the Rear Chassis Blower/Bracket and Air Flow Guide"
in Chapter 2, "Opening and Closing the HP Netserver."
- HP Netserver LP 2000r 1
- User Guide 1
- (1.13 and 1.26 GHz) 1
- Audience Assumptions 2
- Contents 3
- Front Panel 7
- LED ICON Description 9
- Rear Panel 10
- Powering-Up the HP Netserver 12
- Sleep States (ACPI) 13
- Netserver 15
- Replacing the Front Bezel 16
- Removing the Top Cover 16
- Replacing the Top Cover 17
- Air Flow Guide 19
- Removing the PCI Card Cage 20
- Replacing the PCI Card Cage 21
- Boot Priority 25
- Hardware Mirroring 26
- Top Connector 34
- Bottom Connector 34
- Installing Additional DIMMs 38
- Removing DIMMs 42
- IRQ Settings 46
- I C Connector 47
- Integrated 48
- RA Board 48
- Connector 48
- Removing an Accessory Board 53
- Primary Processor (CPU1) 56
- Secondary 56
- Processor 56
- ZIF Lever 59
- Terminator 59
- Installing the Heatsink 61
- (4-Post) 67
- Marking Rack Columns 71
- Anti-tip Foot 72
- Extended 72
- Screws (4) 72
- (2-Post) 81
- Preparing the HP Netserver 86
- Mouse, and Power Supplies 93
- Release Lever 96
- HP Management Solutions 101
- DiagTools 102
- Setup (BIOS) Utility 102
- Accessing the Setup Utility 103
- Menu Bar 103
- Using the Setup Screens 104
- ➢Power-On Password 106
- ➢Hardware Security 106
- SCSI Configuration Utility 107
- Overview 109
- 12 Troubleshooting 111
- Common Installation Problems 112
- Netserver Will Not Power On 113
- Chapter 12 Troubleshooting 114
- Resetting a Lost Password 116
- Hardware Problems 117
- CD-ROM Drive Does Not Work 118
- SCSI Device Does Not Work 118
- Replacing a Battery 119
- Introduction 121
- Tools Required 123
- Rack Configuration Tools 123
- Safety Precautions 124
- Marking the Columns 125
- See Figure 13-5 128
- Attaching the Front Bezel 131
- Cabling Rack Components 132
- A Specifications 135
- Appendix A Specifications 136
- System Board Layout 138
Powiązane produkty i podręczniki dla Sprzęt komputerowy Hp Netserver L Server series
(213 strony)Audio Authority Motherboards user manuals
The list of Audio Authority Motherboards products contains 1 user manuals for 1 models. All pdf user’s guides are available for download or viewing online.
Komentarze do niniejszej Instrukcji