Hp ProLiant BL495c G6 Server-Blade Instrukcja Użytkownika Strona 41
- Strona / 90
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
The auto-c e first time. During the
power-up sequence, the system ROM automatically configures the entire system without needing any
ion. During this process, the ORCA utility, in most cases, automatically configures the array to a
defa lt se
onfiguration process automatically runs when you boot the server for th
intervent
u tting based on the number of drives connected to the server.
NOTE: The server may not support all the following examples.
NOTE: If th oot drive is not empty or has been written to in the past, ORCA does not
automatically configure the arra ust run ORCA to configure the array settings.
e b
y. You m
Drives installed Drives used RAID level
1 1 RAID 0
2 2 RAID 1
3, 4, 5, or 6 3, 4, 5, or 6 RAID 5
More than 6 0 None
To change any ORCA default settings and override the auto-configuration process, press the F8 key w
prompted.
hen
age, operating system, and
primary boot controller), execute RBSU by pressing the
F9 key when prompted. After the settings are
exit RBSU and allow the server to reboot automatically.
D
By default, the auto-configuration process configures the system for the English language. To change any
default settings in the auto-configuration process (such as the settings for langu
selected,
For more information on RBSU, see the
HP ROM-Based Setup Utility User Guide on the Documentation C
or the
HP website (http://www.hp.com/support/smartstart/documentation).
Boot options
l
s co oot from a supported boot device. During this time, you can do
• Access RBSU by pressing the F9 key.
em Maintenance Menu (which enables you to launch ROM-based Diagnostics or
BIOS S
RBSU
remotely through a serial connection to the server COM port. The server that you are remotely configuring
rd and mouse.
Near the end of the boot process, the boot options screen is displayed. This screen is visible for severa
e nds before the system attempts to b
the following:
• Access the Syst
Inspect) by pressing the
F10 key.
• Force a PXE Network boot by pressing the F12 key.
erial Console
BIOS Serial Console allows you to configure the serial port to view POST error messages and run
does not require a keyboa
For more information about BIOS Serial Console, see the
BIOS Serial Console User Guide on the
Documentation CD or the
HP website (http://www.hp.com/support/smartstart/documentation).
Software and configuration utilities 41
- User Guide 1
- Intended audience 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs 7
- System board components 8
- System maintenance switch 9
- HP c-Class Blade SUV Cable 10
- Operations 11
- Remove the server blade 12
- Remove the access panel 12
- Install the access panel 13
- Overview 14
- Connecting to the network 17
- Installing a server blade 17
- Completing the configuration 18
- Introduction 19
- Hard drive option 19
- Memory option 20
- Advanced ECC memory 21
- DIMM installation guidelines 21
- DIMM population order 21
- Installing DIMMs 21
- Processor option 23
- Mezzanine card option 28
- Cabling 30
- Network-based PXE deployment 34
- Deployment infrastructure 35
- PXE deployme 36
- CD-RO oyme 37
- M depl nt 37
- Diskette 38
- image deployment 38
- Configuration too 39
- M-Based Setup Utility 40
- Boot options 41
- C nfiguration Utility 42
- Re-enteri 43
- ROMPaq utility 44
- t hnology 44
- Erase Utility 44
- • and the criticality of 46
- Redundant ROM support 47
- • RBSU 48
- • POST 48
- • Diagnostics 48
- • DOS 48
- • Operating environments w 48
- HP Insight D 49
- Integrated Management Log 49
- Keeping the system current 50
- • Works offline and online 51
- Care Pack 52
- Troubleshooting 53
- Importa s 54
- Symptom information 55
- Service notifications 56
- Loose connections 56
- Troubleshooting flowcharts 56
- Start diagnosis flowchart 57
- General diagnosis flowchart 58
- • The server does not p 60
- POST problems flowchart 62
- Item Refer to 63
- • the HP ProLiant Servers 63
- OS boot problems flowchart 64
- • Hard drive s 65
- • rve or 66
- • Redundancy failure 67
- Troubleshooting 68 68
- Battery replacement 69
- Class B equipment 70
- FCC rating label 70
- Class A equipment 70
- Modifications 71
- • Low Voltag 72
- • EMC Dir 72
- Japanese notice 73
- BSMI notice 73
- Korean notice 73
- Laser compliance 74
- Electrostatic discharge 76
- Specifications 77
- Technical support 78
- Technical support 79 79
- • Obbligatorie – Parti che d 80
- Technical support 81 81
- Customer Self Repair 82
- Reparo feito pelo cliente 82
- Technical support 83 83
- Technical support 84 84
- Technical support 85 85
- Acronyms and abbreviations 86
- Index 88 88
- Index 89 89
- Index 90 90
Powiązane produkty i podręczniki dla Sprzęt komputerowy Hp ProLiant BL495c G6 Server-Blade
(82 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.110 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji