Hp ProLiant BL495c G6 Server-Blade Instrukcja Użytkownika Strona 9
- Strona / 90
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
System maintenance switch
Position Function Default
1* iLO 2 security override Off
2 Configuration lock Off
3 Reserved Off
4 Reserved Off
5* Password disabled Off
6* Reset configuration Off
7 Reserved Off
8 Reserved Off
*To access redundant ROM, set S1, S5, and S6 to ON.
System maintenance switch procedures
When you perform troubleshooting steps, this guide may instruct you to perform the following procedures:
• Clear the system configuration ("Clearing the system configuration" on page 9).
• Access the redundant ROM ("Accessing the redundant ROM" on page 10).
To complete these procedures, you must change physical settings on the system maintenance switch.
Clearing the system configuration
RBSU can be used to restore the factory default configuration. For more information, see "HP ROM-Based
Setup Utilit
y (on page 40)." If the system is unable to boot into RBSU, use the following steps to clear the
system configuration:
1. Power down the server blade (on page 11).
2. Remove the server blade (on page 12).
3. Remove the access panel (on page 12).
4. Change position 6 of the system maintenance switch to on.
5. Install the access panel (on page 13).
6. Install the server blade in the enclosure and power up the server blade.
7. Wait for the POST message that prompts you to change the switch setting:
Maintenance switch detected in the "On" position.
Power off the server and turn switch to the "Off" position.
8. Repeat steps 1 through 3.
9. Change position 6 of the system maintenance switch to off.
10. Repeat steps 5 through 7.
IMPORTANT: When the server blade boots after NVRAM is cleared, a delay of up to 2
minutes is normal. During this delay, the system appears non-functional. Do not attempt any
procedures during the delay.
Component identification 9
- User Guide 1
- Intended audience 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs 7
- System board components 8
- System maintenance switch 9
- HP c-Class Blade SUV Cable 10
- Operations 11
- Remove the server blade 12
- Remove the access panel 12
- Install the access panel 13
- Overview 14
- Connecting to the network 17
- Installing a server blade 17
- Completing the configuration 18
- Introduction 19
- Hard drive option 19
- Memory option 20
- Advanced ECC memory 21
- DIMM installation guidelines 21
- DIMM population order 21
- Installing DIMMs 21
- Processor option 23
- Mezzanine card option 28
- Cabling 30
- Network-based PXE deployment 34
- Deployment infrastructure 35
- PXE deployme 36
- CD-RO oyme 37
- M depl nt 37
- Diskette 38
- image deployment 38
- Configuration too 39
- M-Based Setup Utility 40
- Boot options 41
- C nfiguration Utility 42
- Re-enteri 43
- ROMPaq utility 44
- t hnology 44
- Erase Utility 44
- • and the criticality of 46
- Redundant ROM support 47
- • RBSU 48
- • POST 48
- • Diagnostics 48
- • DOS 48
- • Operating environments w 48
- HP Insight D 49
- Integrated Management Log 49
- Keeping the system current 50
- • Works offline and online 51
- Care Pack 52
- Troubleshooting 53
- Importa s 54
- Symptom information 55
- Service notifications 56
- Loose connections 56
- Troubleshooting flowcharts 56
- Start diagnosis flowchart 57
- General diagnosis flowchart 58
- • The server does not p 60
- POST problems flowchart 62
- Item Refer to 63
- • the HP ProLiant Servers 63
- OS boot problems flowchart 64
- • Hard drive s 65
- • rve or 66
- • Redundancy failure 67
- Troubleshooting 68 68
- Battery replacement 69
- Class B equipment 70
- FCC rating label 70
- Class A equipment 70
- Modifications 71
- • Low Voltag 72
- • EMC Dir 72
- Japanese notice 73
- BSMI notice 73
- Korean notice 73
- Laser compliance 74
- Electrostatic discharge 76
- Specifications 77
- Technical support 78
- Technical support 79 79
- • Obbligatorie – Parti che d 80
- Technical support 81 81
- Customer Self Repair 82
- Reparo feito pelo cliente 82
- Technical support 83 83
- Technical support 84 84
- Technical support 85 85
- Acronyms and abbreviations 86
- Index 88 88
- Index 89 89
- Index 90 90
Powiązane produkty i podręczniki dla Sprzęt komputerowy Hp ProLiant BL495c G6 Server-Blade
(82 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji