HP Remote Graphics Software (RGS) Instrukcja Użytkownika Strona 59
- Strona / 122
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
1. Open Device Manager in the Windows Control Panel.
2. Expand Network adapters.
3. Right-click the network adapter you want to configure, and then select Properties.
4. Click the Advanced tab.
5. In the list of properties, locate the property that controls the speed and duplex setting. The name can
vary, but it is usually something like Speed & Duplex or Link Speed & Duplex.
6. From the Value drop-down list, select the fastest speed your network can support, and be sure to select
the Full Duplex version of that speed.
To configure a network interface to force a particular network speed on Linux:
▲
As root, use a command like in the following example. This example sets network interface 0 as a 100
Mb/sec connection running full duplex mode:
$ /usr/local/sbin/ethtool -s eth0 speed 100 duplex full autoneg off
If you are not satisfied with your network performance, look at the log files on your network switch (if the
local computer is connected to one). A significant number of errors on the switch port may indicate that the
computer or network is not configured correctly. Work with your IT organization to optimize your computer
and network configuration.
Display resolution and layout matching
Many RGS scenarios require that the resolution and display layout transmitted by the sending computer
match the display configuration on the receiving end. The following sections describe how to configure the
sending computer for both Windows and Linux scenarios if RGS is unable to match the resolution and display
layout by default.
Matching display resolution and layout on Windows
When using the Windows version of the RGS Sender, RGS will automatically try to set the resolution and
display layout of the sending computer to match that of the receiving computer (see
Connection settings
on page 33 for more information about the settings that enable this functionality by default). However, there
are some scenarios where some manual configurations might be required to achieve the desired result, such
as when the sending computer has no monitor attached.
When attempting to match the resolution and display layout, the most important thing to remember is that
the sending computer must support the same resolution and layout as the receiving computer.
To avoid possible resolution-matching problems, test the resolution in advance using the following
procedure:
1. Establish an RGS connection with the Match Receiver display resolution setting disabled.
2. When the connection is established, manually attempt to set the sending computer’s resolution to the
match the receiving computer’s resolution.
If you can match the resolution, then RGS can also do it for you automatically.
If you cannot match the resolution, see the additional information in this section.
Depending on the NVIDIA GPU hardware and driver you are using, you might need to perform additional
configurations on the sending computer. The required configurations can vary depending on the hardware, as
described below:
Display resolution and layout matching 47
- User Guide 1
- Acknowledgments 3
- About this guide 5
- Table of contents 7
- 1 Getting started in Windows 13
- 2RGS overview 14
- Typical RGS deployment 15
- User interface overview 16
- Remote Display Window 17
- Remote Display Window toolbar 18
- RGS features 19
- 8 Chapter 2 RGS overview 20
- RGS licensing 21
- Connection types 21
- Multi-monitor configurations 22
- RGS login methods 22
- Easy Login 23
- Single Sign-on 23
- Installing RGS on Windows 24
- Command Description 27
- /wanimprovement 27
- Installs HP Velocity 27
- Installing RGS on Linux 30
- 4 Pre-connection checklist 35
- Using RGS through a firewall 38
- 5 Using the RGS Receiver 40
- Creating an RGS connection 41
- Table 5-2 RGS touch gestures 42
- Connection settings 45
- Performance settings 46
- Audio settings 47
- Network settings 48
- Hotkey settings 48
- Logging settings 49
- Statistics 50
- 7 Using the RGS Sender 51
- RGS Sender GUI (Windows only) 53
- 8 Advanced RGS features 55
- Collaboration 56
- Optimizing RGS performance 57
- Configuring the X server 61
- Remote Audio 63
- Remote Audio on Linux 64
- Configuring audio on Linux 65
- Remote Clipboard 66
- Remote USB 66
- Local/Remote USB overview 67
- Auto-remoting 67
- Supported USB devices 68
- Remoting USB microphones 68
- Unique smart card handling 69
- Verifying the USB data 72
- Directory file format 73
- Auto-launching connections 76
- HPRemote log format 77
- Agent design issues 81
- Administrator alerts 82
- Sample agent 83
- Connection 88
- RGS security features 88
- Full-screen crosshair cursors 90
- 9 RGS properties 92
- Property syntax 93
- RGS Receiver properties 94
- RGS Receiver properties 83 95
- Experience properties 96
- Browser properties 97
- Audio properties 97
- Microphone properties 97
- USB properties 98
- Network properties 98
- Hotkey properties 99
- Clipboard properties 100
- Logging properties 100
- Registration properties 101
- Proxy server properties 101
- 90 Chapter 9 RGS properties 102
- RGS Sender properties 103
- 92 Chapter 9 RGS properties 104
- RGS Sender properties 93 105
- 94 Chapter 9 RGS properties 106
- RGS support matrix 107
- Keyboard locale support 109
- Application support 110
- B Troubleshooting 111
- RGS Sender network timeout 112
- Network timeout issues 113
- Troubleshooting Remote Audio 114
- Troubleshooting Remote USB 116
- RGS error messages 117
- RGS error messages 107 119
- CHP support 120
Powiązane produkty i podręczniki dla Oprogramowanie HP Remote Graphics Software (RGS)
(243 strony)
(83 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji